Refer to the exhibit. A network administrator assumes a task to complete the connectivity between PC A and the File Server. Switch A and Switch B have been partially configured with VLANs 10, 11, 12, and 13. What is the next step in the configuration? A. Add PC A to VLAN 10 and the File Server to VLAN 11 for VLAN segmentation B. Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation C. Add a router on a stick between Switch A and Switch B allowing for Inter-VLAN routing D. Add PC A to the same subnet as the File Server allowing for intra-VLAN communication.
What are the two differences between stateful and deep packet inspection? (Choose two.) A. Deep packet inspection is capable of TCP state monitoring only, and stateful inspection can inspect TCP and UDP. B. Stateful inspection is capable of packet data inspections, and deep packet inspection is not. C. Deep packet inspection is capable of malware blocking, and stateful inspection is not. D. Stateful inspection is capable of TCP state tracking, and deep packet filtering checks only TCP source and destination ports. E. Deep packet inspection operates on Layer 3 and 4, and stateful inspection operates on Layer 3 of the OSI model.
Which two IP addressing schemes provide internet access to users on the network while preserving the public IPv4 address space? (Choose two.) A. IPv6 addressing B. PAT with private internal addressing C. single public Class A network D. private networks only E. custom addresses from ARIN.
Refer to the exhibit. How much OSPF be configured on the GigabitEthernet0/0 interface of the neighbor device to achieve the destined neighbor relationship? A. Router(config)#interface GigabitEthernet 0/0 Router(config-if)#ip ospf cost 5 B. Router(config)#interface GigabitEthernet 0/0 Router(config-if)#ip ospf priority 1 C. Router(config)#interface GigabitEthernet 0/0 Router(config-if)#ip ospf area 2 D. Router(config)#interface GigabitEthernet 0/0 Router(config-if)#ip ospf network point-to-point.
Refer to the exhibit. The router R1 is in the process of being configured. Routers R2 and R3 are configured correctly for the new environment. Which two commands must be configured on R1 for PC1 to communicate to all PCs on the 10.10.10.0/24 network? (Choose two.) A. ip route 10.10.10.0 255.255.255.0 192.168.2.3 B. ip route 10.10.10.10 255.255.255.255 192.168.2.2 C. ip route 10.10.10.10 255.255.255.255 g0/1 D. ip route 10.10.10.8 255.255.255.248 g0/1 E. ip route 10.10.10.0 255.255.255.248 192.168.2.2.
Refer to the exhibit. All routers in the network are configured. R2 must be the DR. After the engineer connected the devices, R1 was elected as the DR. Which command sequence must be configured on R2 to be elected as the DR in the network? A. R2(config)#intergface gi0/0 R2(config-if)#ip ospf priority 100 B. R2(config)#router ospf 1 R2(config-router)#router-id 192.168.2.7 C. R2(config)#router ospf 1 R2(config-router)#router-id 10.100.100.100 D. R2(config)#intergface gi0/0 R2(config-if)#ip ospf priority 1.
Refer to the exhibit. How will switch SW2 handle traffic from VLAN 10 on SW1? A. It sends the traffic to VLAN 10. B. It sends the traffic to VLAN 100. C. It drops the traffic. D. It sends the traffic to VLAN 1.
Refer to the exhibit. If OSPF is running on this network, how does Router2 handle traffic from Site B to 10.10.13.128/25 at Site A? A. It sends packets out of interface Fa0/1. B. It sends packets out of interface Fa0/2. C. It load-balances traffic out of Fa0/1 and Fa0/2. D. It is unreachable and discards the traffic.
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs.
All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration? A. These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)# network 172.19.0.0 B. These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0 C. These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172.19.0.0 D. No further routing configuration is required.
Refer to the exhibit. Which action establishes the OSPF neighbor relationship without forming an adjacency? A. modify hello interval Most Voted B. modify process ID C. modify priority D. modify network type.
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link.
The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.
Based on the information in the graphic, what is the cause of this problem? A. The OSPF area is not configured properly. B. The priority on R1 should be set higher. C. The cost on R1 should be set higher. D. The hello and dead timers are not configured properly. E. A backup designated router needs to be added to the network. F. The OSPF process ID numbers must match.
|
