Refer to the exhibit. What two conclusions should be made about this configuration? (Choose two.) A. The root port is FastEthernet 2/1 B. The designated port is FastEthernet 2/1 C. The spanning-tree mode is PVST+ D. This is a root bridge E. The spanning-tree mode is Rapid PVST+.
Which technology is used to improve web traffic performance by proxy caching? A. WSA B. Firepower C. ASA D. FireSIGHT.
On a corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs? A. a router with subinterfaces configured on the physical interface that is connected to the switch B. a router with an IP address on the physical interface connected to the switch C. a switch with an access link that is configured between the switches D. a switch with a trunk link that is configured between the switches.
Which three statements are typical characteristics of VLAN arrangements? (Choose three.) A. A new switch has no VLANs configured. B. Connectivity between VLANs requires a Layer 3 device. C. VLANs typically decrease the number of collision domains. D. Each VLAN uses a separate address space. E. A switch maintains a separate bridging table for each VLAN. F. VLANs cannot span multiple switches.
What are two benefits of using VTP in a switching environment? (Choose two.) A. It allows switches to read frame tags. B. It allows ports to be assigned to VLANs automatically. C. It maintains VLAN consistency across a switched network. D. It allows frames from multiple VLANs to use a single interface. E. It allows VLAN information to be automatically propagated throughout the switching environment.
What are two reasons a network administrator would use CDP? (Choose two.) A. to verify the type of cable interconnecting two devices B. to determine the status of network services on a remote device C. to obtain VLAN information from directly connected switches D. to verify Layer 2 connectivity between two devices when Layer 3 fails E. to obtain the IP address of a connected device in order to telnet to the device F. to determine the status of the routing protocols between directly connected routers.
Which type does a port become when it receives the best BPDU on a bridge? A. The designated port B. The backup port C. The alternate port D. The root port.
Refer to the exhibit. How will switch SW2 handle traffic from VLAN 10 on SW1? A. It sends the traffic to VLAN 10. B. It sends the traffic to VLAN 100. C. It drops the traffic. D. It sends the traffic to VLAN 1.
Refer to the exhibit. Which VLAN ID is associated with the default VLAN in the given environment? A. VLAN 1 B. VLAN 5 C. VLAN 10 D. VLAN 20.
match the benefits of a Cisco Wireless Lan Controller dynamic rf feature - optimised user performance - easy upgrade process - easy deployment process - .
Which command should you enter to configure an LLDP delay time of 5 seconds? A. lldp timer 5000 B. lldp holdtime 5 C. lldp reinit 5000 D. lldp reinit 5.
Which two command sequences must be configured on a switch to establish a Layer 3 EtherChannel with an open-standard protocol? (Choose two.) A. interface GigabitEthernet0/0/1 channel-group 10 mode auto B. interface GigabitEthernet0/0/1 channel-group 10 mode on C. interface port-channel 10 no switchport ip address 172.16.0.1 255.255.255.0 D. interface GigabitEthernet0/0/1 channel-group 10 mode active E. interface port-channel 10 switchport switchport mode trunk.
Refer to the exhibit. The network administrator wants VLAN 67 traffic to be untagged between Switch 1 and Switch 2, while all other VLANs are to remain tagged.
Which command accomplishes this task? A. switchport access vlan 67 B. switchport trunk allowed vlan 67 C. switchport private-vlan association host 67 D. switchport trunk native vlan 67.
Refer to the exhibit. Based on the LACP neighbor status, in which mode is the SW1 port channel configured?
A. mode on B. active C. passive D. auto.
match the WLAN components access point - wireless lan controller - service port -
virtual interface - dynamic interface - .
Which configuration ensures that the switch is always the root for VLAN 750? A. Switch(config)#spanning-tree vlan 750 priority 38418607 B. Switch(config)#spanning-tree vlan 750 priority 0 Most Voted C. Switch(config)#spanning-tree vlan 750 root primary D. Switch(config)#spanning-tree vlan 750 priority 614440.
An engineer needs to configure LLDP to send the port description type length value (TLV). Which command sequence must be implemented? A. switch(config-if)#lldp port-description B. switch#lldp port-description C. switch(config-line)#lldp port-description D. switch(config)#lldp port-description.
|
