option
Questions
ayuda
daypo
search.php

FAA Ignition and Starting Systems 1 Turbine

COMMENTS STATISTICS RECORDS
TAKE THE TEST
Title of test:
FAA Ignition and Starting Systems 1 Turbine

Description:
some questions

Creation Date: 2026/11/17

Category: Others

Number of questions: 31

Rating:(0)
Share the Test:
Nuevo ComentarioNuevo Comentario
New Comment
NO RECORDS
Content:

A safety feature usually employed in pneumatic starters that is used if the clutch does not release from the engine drive at the proper time during start is the. flyweight cutout switch. spring coupling release. drive shaft shear point.

The primary advantage of pneumatic (air turbine) starters over comparable electric starters for turbine engines is. a significant lack of wear to the commutator. that it does not disengage until the engine reaches idle. its high power-to-weight ratio.

Pneumatic starters are usually designed with what types of airflow impingement systems?. Radial inward flow turbine and axial-flow turbine. Centrifugal compressor and axial-flow compressor. Double entry centrifugal outward flow and axial-flow turbines.

In a turbine engine DC capacitor discharge ignition system, where are the high-voltage pulses formed?. At the breaker. At the triggering transformer. At the rectifier.

How does the ignition system of a gas turbine engine differ from that of a reciprocating engine?. One igniter plug is used in each combustion chamber. Magneto-to-engine timing is not critical. A high-energy spark is required for ignition.

Which of the following are included in a typical turbine engine ignition system?. Two igniter plugs, two transformers, and two intermediate ignition leads. Two igniter plugs, one exciter unit, and two low-tension igniter leads. Two igniter plugs, one exciter unit, and two high-tension igniter leads.

Igniter plugs used in turbine engines have a long service life because they. have a high intensity spark. Operate continuously with lower spark. Do not require continuous operation.

Great caution should be exercised in handling damaged hermetically sealed turbine engine igniter transformer units because. compounds in the unit may become a fire or explosion hazard when exposed to the air. some contain radioactive material. some contain toxic chemicals.

(Refer to Figure 5.) If wire 8 is broken or disconnected after starter rotation is initiated, and the power lever is advanced, the. starting sequence will continue normally. starter will shut down, but the igniters will continue to fire. starting sequence will discontinue.

Air turbine starters are generally designed so that reduction gear distress or damage may be detected by. characteristic sounds from the starter assembly during engine start. breakage of a shear section on the starter drive shaft. inspection of a magnetic chip detector.

Sharp bends should be avoided in ignition leads primarily because. weak points may develop in the insulation through which high tension current can leak. ignition lead wire conductor material is brittle and may break. ignition lead shielding effectiveness will be reduced.

Which statement is correct regarding the ignition system of a turbine engine?. The system is normally de-energized as soon as the engine starts. It is energized during the starting and warmup periods only. The system generally includes a polar inductor-type magneto.

A safety feature usually employed in direct-cranking starters that is used to prevent the starter from reaching burst speed is the. drive shaft shear point. stator nozzle design that chokes airflow and stabilizes turbine wheel speed. spring coupling release.

Airflow to the pneumatic starter from a ground unit is normally prevented from causing starter overspeed during engine start by. stator nozzle design that chokes airflow and stabilizes turbine wheel speed. activation of a flyweight cutout switch. a preset timed cutoff of the airflow at the source.

Inspection of pneumatic starters by maintenance technicians usually includes checking the. oil level and magnetic drain plug condition. stator and rotor blades for FOD. rotor alignment.

The purpose of an under current relay in a starter-generator system is to. provide a backup for the starter relay. disconnect power from the starter-generator and ignition when sufficient engine speed is reached. keep current flow to the starter-generator under the circuit capacity maximum.

The constrained-gap igniter plug used in some gas turbine engines operates at a cooler temperature because. it projects into the combustion chamber. the applied voltage is less. the construction is such that the spark occurs beyond the face of the combustion chamber liner.

(Refer to Figure 5.) The type of system depicted is capable of operating with. external power only. either battery or external power. battery power and external power simultaneously.

Why are turbine engine igniters less susceptible to fouling than reciprocating engine spark plugs?. The high-intensity spark cleans the igniter. The frequency of the spark is less for igniters. Turbine igniters operate at cooler temperatures.

When using an electric starter motor, current usage. is highest at the start of motor rotation. remains relatively constant throughout the starting cycle. is highest just before starter cutoff (at highest RPM).

In the event a pneumatic start valve will not operate and the manual override must be used, the starter T-handle must be closed at scheduled starter drop out because. the starter will overheat. the starter will overspeed at a given N(2). the starter oil will be blown overboard.

Why do turbine engine ignition systems require high energy?. To ignite the fuel under conditions of high altitude and high temperatures. Because the applied voltage is much greater. To ignite the fuel under conditions of high altitude and low temperatures.

(Refer to Figure 5.) Which malfunctions will allow the igniters to operate when tested but be inoperative during a start attempt?. Wire 12 and 11 are broken. Wire 11 is broken and/or the ignition relay is inoperative. Wire 10 is broken and/or the ignition relay is inoperative.

A clicking sound heard at engine coast-down in a pneumatic starter incorporating a sprag clutch ratchet assembly is an indication of. gear tooth and/or pawl damage. one or more broken pawl springs. the pawls re-contacting and riding on the ratchet gear.

(Refer to Figure 5.) With power applied to the bus bar, what wire supplies standby power to the starter relay contact?. 4. 7. 8.

Generally, when removing a turbine engine igniter plug, in order to eliminate the possibility of the technician receiving a lethal shock, the ignition switch is turned off and. disconnected from the power supply circuit. the igniter lead is disconnected from the plug and the center electrode grounded to the engine after disconnecting the transformer-exciter input lead and waiting the prescribed time. the transformer-exciter input lead is disconnected and the center electrode grounded to the engine after disconnecting the igniter lead from the plug and waiting the prescribed time.

In a typical starter-generator system, under which of the following starting circumstances may it be necessary to use the start stop button?. Hung start. Hot start. Contacts stick open.

When using an electric starter motor, the current flow through it. is highest just before starter cutoff (at highest RPM). remains relatively constant throughout the starting cycle. is highest at the start of motor rotation.

(Refer to Figure 5.) Which malfunctions will allow the igniters to operate normally during start but be inoperative when tested?. Wire 10 is broken. Wire 14 or 15 is broken. Wire 12 is broken.

(Refer to Figure 5.) When an external power source is connected to the aircraft,. the battery cannot be connected to the bus. both battery power and external power are available to the bus. the starter relay coil has a path to ground.

(Refer to Figure 5.) With power applied to the bus bar, what switch changes will allow the ignition exciters test switch to function?. Engine master switch, battery switch, and power lever switch. Engine master switch, start switch, and test switch. Engine master switch and ignition switch.

Report abuse