HPE6-A66 Aruba Certified Design Associate

When a WLAN has to support nomadic devices, a network architect must primarily plan for which component in their design?. type of users. number of users per location. mobility requirements and usage. density of users.

Which two challenges do 802.11g barcode scanners present to a WLAN design? (Select two.). roaming between APs. encountering RF interference by devices. determining the RF channel bandwidth consumed per Barcode scanner. implementing adequate security measures to ensure PCI compliance. providing consistent performance on all available channels.

A network architect is creating a new wireless solution for a customer. Wireless coverage is required throughout all four floors of two buildings on the same campus. Dynamic RF capabilities, including AirMatch, are required. Seamless roaming is required within and between the two buildings. Each floor will have approximately 20 APs and 6 external APs are required for connectivity between the two buildings. Given this information, which Aruba solution would be the most cost-effective while still meeting the customer's requirements?. An IAP cluster per floor. A standalone 7008 controller per floor. Two 7205 mobility controllers in a cluster. Two 7030 mobility controllers in a cluster.

Which must you perform in IRIS to assign a device to a Design Group?. Right-click the device and select Set Layer Membership. Right-click the device and select Set Design Group. Drag and drop the device into the Site. Drag and drop the device into the Design Group.

A network architect is designing a wireless solution for a company that is leasing one floor in a multifloor building in a downtown area. The customer is concerned about ensuring complete Wi-Fi coverage and pinpointing RF hazards. What type of survey should the network architect perform?. Active. Virtual. Passive. Spectrum clearing.

A customer placed an order for an ArubaOS 5406R switch and plans to rack mount it in a wiring closet. The dimensions of the switch are 17.5 inches wide (44.45 cm), 6.9 inches high (17.5 cm), and 17.75 inches deep (45.1 cm). How many rack units should a customer plan for this switch?. 5. 4. 6. 3.

A wiring closet with a POE+ switch is 250 feet (76 meters) away from an AP on a building floor. The AP's smart-rate port is connected to a smart-rate port on the switch, which is capable of 10 Gbps. The cable type is Cat5e STP. What is the maximum speed that the customer can expect from the connected AP?. 2.5 Gbps. 1 Gbps. 5 Gbps. 10 Gbps.

A customer has some employees that travel to various locations, where these employees will need Wi-Fi access at these locations. Because many of these locations do not have wireless support, the employees will need to carry an AP solution with them. Internet connectivity, if it doesn't exist at these locations, will be provided by a national phone company USB wireless card which will be connected to AP. The wireless solution needs minimal bandwidth, but needs to minimally support 802.11ac wave 1 devices. Which Aruba AP wireless solution would meet the needs of these employees most effectively and cost efficiently?. 318. 303H. 365. 203R.

NewStellar has a main corporate campus in a business park with two adjacent buildings. Each building has three floors and each floor is 322 x 175 feet (98 x 53 meters) for 56,350 square feet (5,235 square meters) total. The ceiling for each floor is 12 feet (3.6 meters) high with a drop-down ceiling at 10 feet (3 meters). The network architect has given you one floor to analyze, Building 1 Floor 2, shown in the attached exhibit. This floor has a central main corridor with washrooms, stairs, elevators and supply and network cabinets. There are cubicles around the perimeter of the floor. The central part main corridor's dimensions contain 9,350 square feet (870 square meters). Assuming that wireless coverage is not required in the central area, which square footage (square meter) value should a network architect use when determining the number of APs in a capacity design for each floor?. 55.750 square feet (5,175 square meters). 56.350 square feet (5,235 square meters). 47.000 square feet (4,365 square meters). 338,100 feet (31,410 square meters).

A network architect is redesigning a wireless network. The architect begins by analyzing the number of spatial streams supported by APs of various vendors as well as the wireless devices currently in the network, if the company wants to ensure that new wireless design, including user wireless devices, support Multi-User MIMO (MU-MIMO). which standard or standards must the wireless products support?. Only 802.11ax and 8011.ac. Only 802.11ax. Only 802.11ax,802.11ac, and 802.11n. Only 802.11ax,802.11ac, 802.11n, and 802.11a.

A network architect is given the task to design a new network solution for NewStellar Company, Inc. NewSteiiar has a main corporate campus in a business park with two adjacent buildings. The network architect has given one floor to analyze, Building 1 Floor 2, shown in the attached exhibit. Each building has three floors and each floor is 322 x 175 feet (98 x 53 meters) for 56,350 square feet (5,235 square meters) total, which results in a total of 338,100 feet (31,410 square meters) for the entire building space. Each floor has a central main corridor with washrooms, stairs, elevators and supply and network cabinets. There are cubicles around the perimeter of the floor. The central part main corridor's dimensions contain 9,350 square feet (870 square meters). Because of security concerns, video cameras will be installed throughout the facility. There are 16 of these per floor, 8 per wiring closet. The cameras are non-WiFi capable and require POE 802.3af capable switch ports from which to draw power. A wireless capacity design is required. Assuming that wireless coverage is required across the Building 1, Floor 2, including the central area, and that half the required APs will connect to each wiring closet, approximately how many POE+ ports will be required per wiring closet for all devices that have POE or POE+ needs?. 30. 22. 42. 8.

When planning the use of Cat7 cabling for a SmartRate connection between an ArubaOS AP and an ArubaOS switch, which sections should be considered when calculating distance?. A + C. A + B. A + B + C + D. A + B + C.

A company is redesigning their wireless network and will be upgrading all devices to support the latest wireless standards. The company is not near any radar installations. In order to keep wireless NIC power levels as low as possible to reduce interference issues and to take advantage of radar frequency ranges, what IEEE standard should APs support?. 802.11r. 802.11ax. 802.11v. 802.11h.

A network architect has created two sites in IRIS and defined network devices for each site. From which window would a network architect connect the two sites together?. Topology. Site-1. Catalog. Start Page.

A network architect is creating a new wired design for a warehouse building. As a best practice, what length should the architect allow for the service loop in the wiring closets in this environment?. 3-10 feet (1-3 m). 3 feet (1 m). 15-30 feet (5-10 m). 30-60 feet (10-20 m).

A customer requires a campus core virtualization solution that supports a dual control and management planes, as well as active-active forwarding paths. Which solution would meet the customer's requirements?. Mesh stacking. VSX. Backplane stacking. VSF.

A company has two buildings on a campus that are approximately 700 feet (214 meters) apart with a clear line of site. No fiber exists between the buildings; however, there is a need for connecting the networks in the buildings together. The connection between the two buildings will need to support peak rates over 1 Gbps. Which solution should the company choose that will meet their requirements as well as being costeffective?. Two outdoor AP 367s. Two outdoor AP 387s. Two outdoor AP 510s. Multi-mode fiber between campus switches.

A university department has a program in video processing and editing. Students in the department use Wi-Fi to interact with the video servers. The editing and processing is done by the students accessing and using the video servers. However, the students must then stream their results, via Wi- Fi to their laptops to verify the results. A network architect has determined that no more than 20 APs will be needed for the Wi-Fi solution. Because of the large amount of bandwidth used during the streaming, the Aruba mobility controller solution will need to support 10 Gbps links. Which solution would cost-effectively meet this customer's requirements?. 7008. 7205. 7240XM. 7030.

A network architect imports a floorplan defined in a PNG file format What is the function of the measurement tool in Aruba's VisualRF?. Define the appropriate dimensions of each object in a Floorplan View. Define the appropriate dimensions of a Floorplan and Building View. Define the appropriate dimensions of a Floorplan View. Define the appropriate dimensions of each room in a Floorplan View.

A company needs an upgrade of its access layer switches. The solution requires that devices connected to the access layer by authenticated and their traffic processed by the firewall features of the Aruba Mobility Controllers. Which solution should the company implement?. PAPI mobility. Dynamic segmentation. iPsec tunneling. GRE tunneling.

A customer is purchasing Aruba 555 APs for a new wireless network. The APs will be pre-staged as campus APs (CAPs) and be managed by a controller solution During the pre-staging process, console access to the APs might be necessary Which console connection cable should the customer purchase for the 555 APs?. RJ-45. RS-232. USB-A. Micro-B USB.

A company needs to replace an existing legacy wireless and wired solution with one that supports features like 802 11ax for APs and logical switching for switches. The company is located on a single floor with two wiring closets. Assume that there will be 10 APs connected via POE+ to each wiring closet, along with 36 wired user connections All switches on a floor should be configured in a single stack. The distance between wiring closets is 100 feet (31 meters). Which switching solution will minimally provide 10 Gbps uplinks at the most costeffective price, while still meeting the company's requirements?. 2930M switches. 2930F switches. 5406R switches. 3810M switches.

A customer has a need to track traffic patterns and anomalies on a pair of ArubaOS-CX 8400 series switches. Which technology will the customer need to deploy for these switches?. Mobility Controller. NetEdit. Network Analysis Engine. Clearpass.

A company has a warehouse that requires ruggedized APs to provide wireless access The APs need to support these characteristics: 2 or more spatial streams 802.11ac and 802.11n support Cat 7 Ethernet cabling will be used to connect the APs to POE+ capable switches Link aggregation should be employed between the APs and the Ethernet switches. Which would be the most costeffective solution that would meet the company's requirements?. AP 375 with external omnidirectional antennas. AP 365 with integrated omnidirectional antennas. AP 318 with external omnidirectional antennas. AP 510 with external omnidirectional antennas and plastic AP cover.

A high-end theater venue will be implementing an Aruba wireless solution using ceiling- and wallmounted APs. The venue wants to ensure the the APs blend into the ceiling and wall environments. What solution should the customer use to ensure that wireless coverage is not hampered?. Place the APs above the ceiling and behind the walls. Place a strip of tape over the LEDs. Order Aruba AP covers for the APs. Paint the APs to match the ceilings or walls.

A network architect is designing a new Wi-Fi solution for a small university The solution will involve two mobility controllers that will be clustered at the campus core Because students use a lot of video in both the dormitory rooms and in the classrooms, the solution will need to support 50Gbps via link aggregation between the controllers and core switches. Which solution would most cost-effectively meet this requirement for the campus core?. Aruba 7220 mobility controllers and 3810M switches. Aruba 7210 mobility controllers and 5406R switches. Aruba 7240XM mobility controllers and 3810M switches. Aruba 7280 mobility controllers and 5406R switches.

NewRocket requires a wireless capacity design 30 Aruba 510 APs will be connected to each wiring closet using SmartRate connections. Wireless coverage needs to be provided even if a POE+ switch loses power Because of security concerns, wired video cameras were recently installed throughout the facility. There are 12 of these per floor. 6 per wiring closet. The cameras are 802.11n WiFi capable and have power injectors from which to draw power. Based on the POE+ needs of the mentioned devices, which solution would meet the POE+ requirements while still providing a redundant and cost-effective Wi-Fi solution for the devices that require POE+ for Building 1, Floor 2?. One 3810M 40G 8 HPE Smart Rate switch. Two 2930F 24-port POE+ switches. Two 2930M 24-port POE+ switches. One 2930M 48-port POE+ switch.

What is the main key for a network design to ensure users have a good experience running their applications'?. Provision adequate bandwidth. Provide appropriate AP density. Determine the number of users per location. Implement appropriate security controls.

A company has two buildings on a campus, where each building has three floors, with two wiring closets per floor Assume that there will be 24 APs connected via POE+ to each wiring closet, along with 128 wired user connections. Which backplane stacking solution will provide the necessary Ethernet port capacity for all devices on Building 1 Floor 2 and is fully meshed?. Two 3810M 24-port POE+ switches and three 3810M 48-port switches per wiring closet. Two 2930F 24-port POE+ switches and three 2930F 48-port switches per wiring closet. One 2930M 24-port POE+ switch and two 2930M 48-port switches per wiring closet. One 3810M 24-port POE+ switches and two 2930M 48-port switches per wiring closet.

When determining a customer's agenda and clarifying their expectations for a new HPE/Aruba deployment, which two questions should be asked during the stakeholder checklist? (Select two.). What business problems are you trying to solve?. What is the networking experience of onsite personnel?. Which help desk system is deployed?. is a request for proposal or actual bill of materials (BOM) required?. What is your anticipated growth of the environment?.

A network architect plans to use two ArubaOS 5406 switches in a wiring closet configured in a VSF domain The VSF link requires a 40 Gbps connection Which SFP+ transceiver solutions would meet this requirement?. QSFP+ LC. SFP. SmartRate. QSFP28.

A network designer is documenting the number of physical sites for a customer that is within the scope of a redesign project. When determining the network purpose at each site, on what should the designer focus at each site? (Select two.). types of users and their devices. ceiling height. square footage. number of buildings. number of users.

A network architect is redesigning the access layer in a data center for a customer. The access layer requires fixed-port switches that support VSF and data center features like L2 VXLAN and REST-API Which switching solution should the network architect recommend?. 8400. 3810M. 2930F. 6300.

Which AP mode allows an AP to operate autonomously?. IAP. AM. RAP. CAP.

NewStellar has a main corporate campus in a business park with two adjacent buildings that are 150 feet apart (46 meters). This is an open campus with no obstructions between the two buildings Each building has three floors and each floor is 322 x 175 feet (98 x 53 meters) for 56,350 square feet (5,235 square meters) total, which results in a total of 338,100 feet (31,410 square meters) for the entire building space. The ceiling for each floor is 12 feet (3.6 meters) high with a drop-down ceiling at 10 feet (3 meters) The network architect has given one floor to analyze. Building 1 Floor 2 shown in the attached exhibit. This floor has a central main corridor with washrooms, stairs, elevators and supply, and network cabinets. There are cubicles around the perimeter of the floor. The central part main corridor's dimensions contain 9,350 square feet (870 square meters). The company has determined that Wi-Fi coverage will not include the central area of each floor, which includes the washrooms, stairs, elevators and supply and network cabinets. Based on a capacity design, approximately how many APs should a network architect add to each floor to plan the design in VisuaiRF?. 40. 10. 20. 30.

A network architect is replacing an old wireless implementation based on 802.11a with a new wireless solution. The company has a lot of money invested in legacy wireless barcode scanners and will not be replacing them. However, the bandwidth that the company expects each AP to have less than 700 Mbps in bandwidth, and this is not expected to change in the future. Which wireless solution would best meet this company's needs and be the most cost-effective?. 802.11n. 802.11ax. 802.11g. 802.11ac.

A company is installing Internet of Things (loT) devices to support a smart and energy-efficient environment for a building, including loT devices for heating and air conditioning, lights, and window shades. loT devices of these types are typically classified as which category of devices?. Nomadic devices. Somewhat mobile devices (SMD). Highly mobile devices (HMD). Stationary devices.

A network architect needs to design a new wireless solution for a small company The architect estimates that about 150 APs will be required to implement a capacity design. Roaming support is required. Also, the design requires meshing to connect some of the APs to the network. The customer requires that client state synchronization be provided for real-time failover. Which solution would most cost-effectively meet these requirements?. lAPs in a cluster. FRAPs in a cluster. Two 7205 mobility controller and campus APs in a cluster. Two 7030 mobility controller and campus APs in a cluster.

A network architect is designing a new Wi-Fi solution for a customer The customer currently occupies a onestory building on a small campus. In one part of the building there is an auditorium, where the ceiling height and attenuation is different from the rest of the building. What should the network architect create in VisualRF to identify this difference when planning :ne APs?. Define the appropriate properties in the Network View. Create a Region in the Floorplan View. Spit the Building View into two Floorplan Views. Define the appropriate properties in the Building View.

A network architect has developed a design for a new Aruba Wi-Fi network that will include a virtual Mobility Master (MM) running the ArubaOS 8.4 operating system that will manage: Two clustered 7210 controllers with 600 campus APs Two clustered VMC-50 controllers with 75 remote APs Wireless IPS The architect plans on creating user roles and firewall policies on the controllers as well as implementing AirMatch. What would meet the license requirements for this scenario?. LIC-MM-VA-1000 (X1). LIC-MC-VA-50 (X1), LIC-AP (x675). PEF (X675), RFP (X675). LIC-MM-VA-50 (X1), LIC-MC-VA-50 (x2). LIC-AP (X675), PEF (x675), RFP (X675). LIC-MM-VA-1000 (X1), LIC-MC-VA-50 (x2), LIC-AP (X675). PEF (X675). RFP <x675). LIC-MM-VA-1000 (X1), LIC-MC-VA-50 (x1), LIC-AP (x600). PEF (X600), RFP (x600).

A network architect wants to estimate the number of Aruba APs that will be needed For a new wireless design and determine the wireless coverage using VisualRF. The company requires a high density design. The building has 200.000 square feet. How many APs should the network architect add to VisualRF in order to perform the coverage analysis?. 40. 80. 60. 100.

A network architect will be using VisualRF to determine the appropriate wireless coverage for a new wireless design. Seamless, uninterrupted roaming is necessary for this design, since voice will need to be supported. Given these requirements, which information should be used in VisualRF to plan a cost effective solution that meets these requirements?. Minimum -70db, 1 AP per 2,500 square feet, capacity design. Minimum -65db, 1 AP per 2,500 square feet, high density design. Minimum -80db, 1 AP per 1,000 square feet, very high-density design. Minimum -70db. 1 AP per 5,000 square feet, high density design.

Which feature does the Aruba AP 555 support? (Select two.). 802.11ac and lower standards only. desk wall plate mounted. three radios. weather proof and temperature hardened. high density indoor locations.

A customer requires Aruba switches that support Smart Rate ports to connect to Aruba APs Which switching product should the customer purchase that will provide 24 Smart Rate ports per access layer switch'?. OfficeConnect 1950. Aruba 2930F. Aruba 2930M. Aruba 2540.

A customer currently has sets of three Aruba 5406R switches deployed for an access layer in multiple wiring closets in a building They are clustered in a VSF domain The customer wants to set up Multiple Active Detection (MAD) for the OOBM port, as well as use this port for remote management access. To simplify the connectivity, the customer wants to connect these three switches' OOBM ports to a separate switch in the wiring closet for the OOBM connectivity. Which would be the most cost-effective solution that would meet the customer's requirements?. 2530. 5406R. 2930F. 2930M.

Which IRIS option will automatically create a project with a blank preconfigured Site-1 ?. New Campus. New Express Mode. New Project. New Site.

Which type of Aruba AP uses its radio as its back-haul connection?. Mesh Point. Mesh Portal. Air Monitor (AM). Remote AP (RAP).

A network architect plans to implement channel bonding in a new wireless design that involves dense deployment of APs. Which channel width would be optimal for this design?. 40 MHz. 10MHz. 20 MHz. 60 MHz.

A network architect has developed a design for a new Aruba Wi-Fi network that will include a hardware Mobility Master (MM) running the ArubaOS 8 4 operating system that will manage: Two clustered 7205 controllers with 300 campus APs Two clustered VMC-50 controllers with 75 remote APs The architect plans on creating user roles, firewall policies, and wireless IPS policies on the controllers as well as implementing AirMatch. What would meet the license requirements for this scenario?. LIC-MC-VA-50 (X2), LIC-AP (375), PEF (X375), RFP (X375). LIC-MC-VA-50 (x1), LIC-AP (300), PEF (X300). RFP (x300). LIC-MM-VA-50, LIC-MC-VA-50 (X1), LIC-AP (X300), PEF (x300). RFP (x300). LIC-MM-VA-500. LIC-MC-VA-50 (X2), LIC-AP (x375). PEF (x375). RFP (x375).

A network architect needs to plan a new wireless network. Central only. Airwave and Central only. Airwave, Central, Windows, Mac OSX, and Linux. Airwave, Central, and Windows only.

A network architect is designing a new wired and wireless solution for for a company. The company has two buildings on a campus, which each building has three floors. The campus core will be placed in the basement of Building 1. Each wiring closet has eight strands of multi-mode OM3 grade fiber that connect to a wiring closet of the first floor of the building it is contained, referred to as a main distribution frame (MDF). The maximum distance between a floor's wiring closet and the MDF is 100 feet (30 meters). The maximum distance between the two MDFs and the campus core is no more than 150 feet (45 meters). There are eight strands of multi-mode OM3 grade fiber from these two MDF closets to the campus core. Based on this information, which type of design should be used and what is the maximum speeds supported all uplinks for the existing the multi-mode fiber?. three-tier and 10 Gbps. three-tier and 40 Gbps. two-tier and 10 Gbps. two-tier and 40 Gbps.

A network architect is designing a new wireless solution for a company The company needs seamless roaming and client and AP active load balancing. The company also requires an Aruba Mobility Master (MM) to manage the wireless infrastructure. Which Aruba feature does the architect need to include in the design?. Clustering. AirMatch. Client Match. IAP VC.

A customer has over 100 access layer switches. The customer requires user authentication done via the Aruba Dynamic Segmentation feature. What components are required to implement this solution? (Select two.). Enterprise authentication server. Aruba APs. Aruba mobility controller. AirWave server. Active Directory server.

A customer is designing a new wired network. The customer requires 50 Gbps uplinks, VSF logical switching, and smart rate port support Which of the following switches would meet these requirements?. 3810M series. 6300 series. 5400R series. 8300 series.

Which feature does the Aruba AP 387 support?. 802.11 ax. Indoor usage. included external directional antennas. 60GHz RF.

A network architect is doing a site survey for a new wireless design One concern the company has with the old wireless network is coverage. In some cases, APs would lose power and some employees in the network would lose wireless connectivity. The new design needs to prevent this issue from occurring. During the site survey, what are best practices to be followed in regards to the dBm signal level and the power of the AP to ensure adequate wireless coverage and minimal overlap of AP signals for the new design?. AP power at 75% and a measurement of -90 dBM on the measuring device. AP power at 100% and a measurement of -65 dBM on the measuring device. AP power at 75% and a measurement of -80 dBM on the measuring device. AP power at 50% and a measurement of -65 dBM on the measuring device.

A company has hired a network architect to replace an existing legacy wireless and wired network The building is one-story and contains four wiring closets Based on the information the network architect gathered from the company, one 48-port POE+ switch and three 48-port non-POE+ switches will be placed in each wiring closet. One stacking domain should be created for each wiring closet that supports 40 Gbps uplinks. Which stacking solution should the architect implement for the floor that meets the requirements and is the most cost-effective'?. VSX. VSF. Backplane stacking. Distributed trunking.

Which component uniquely defines the BSSID when implementing an employee SSID?. Case-sensitive SSID name. Radio MAC address. Wireless device MAC address. Case-insensitive SSID name.

A company has chosen an Aruba mobility controller solution for the redesign of their wireless network The design will have two 7205 controllers in a cluster for campus employees and a single VMC-50 virtual controller for remote access via a DMZ. A Mobility Master (MM) is used for centralized license and controller management. All controllers will minimally run ArubaOS 8 4 or later Currently the company has 1.000 employees. There are 30 branch offices that will use RAPs to connect to the DMZ controller. A peak of 100 users concurrently using the VIA client will also connect to the DMZ controller. How many Aruba LIC-VIA licenses does the company need to purchase for this solution?. 100. 1. 1030. 130.

A network architect is designing a Wi-Fi solution for a customer using Aruba Central's VisualRF tool When creating a Campus view, how would the network architect pull in a map that displayed the campus location in a city?. Import the longitude and latitude information from any web-based map site. Import the longitude and latitude information from Google Maps. Create a screen capture from any web-based map site and import the picture file. Use VisualRF's built-in map tool and define the appropriate longitude and latitude information.