identity services engine

Which action is the vSmart controller responsible for in a Cisco SD-WAN deployment? SDDDDDDDDDDDDD-WAN DDDDDDDDDDDddddddddddddddddistribute. A. onboard WAN Edge nodes into the Cisco SD-WAN fabric. B. gather telemetry data from WAN Edge routers. C. distribute policies that govern data forwarding performed within the Cisco SD-WAN fabric. D. handle, maintain, and gather configuration and status for nodes within the Cisco SD-WAN fabric.

Which action is the vSmart controller responsible for in a Cisco SD-WAN deployment?. C. distribute policies that govern data forwarding performed within the Cisco SD-WAN fabric. D. handle, maintain, and gather configuration and status for nodes within the Cisco SD-WAN fabric.

Where is radio resource management performed in a Cisco SD-Access wireless solution?. A. DNA Center. B. control plane node. C. wireless controller. D. Cisco CMX.

How does the RIB differ from the FIB?. C. The RIB is used to create network topologies and routing tables. The FIB is a list of routes to particular network destinations. D. The RIB includes many routes to the same destination prefix. The FIB contains only the best route.

In a Cisco SD-Access fabric, which control plane protocol is used for mapping and resolving endpoints?. A. DHCP. B. VXLAN. C. SXP. D. LISP.

What are two considerations when using SSO as a network redundancy feature? (Choose two.) NSF → L3 supervis are sync'ed. A. requires synchronization between supervisors in order to guarantee continuous connectivity. B. the multicast state is preserved during switchover. C. must be combined with NSF to support uninterrupted Layer 3 operations. D. both supervisors must be configured separately. E. must be combined with NSF to support uninterrupted Layer 2 operations.

In a Cisco SD-Access wireless architecture, which device manages endpoint ID to edge node bindings? endpoint ID to NNNNNNNNNNNNnnnnnnnode bindings fabric ctrl plane NNNNNNNNNNNNnnnnnode. A. fabric control plane node. B. fabric wireless controller. C. fabric border node. D. fabric edge node.

What are two differences between the RIB and the FIB? (Choose two.). A. FIB is a database of routing prefixes, and the RIB is the information used to choose the egress interface for each packet. B. The FIB is derived from the data plane, and the RIB is derived from the FIB. C. The RIB is a database of routing prefixes, and the FIB is the information used to choose the egress interface for each packet. D. The RIB is derived from the control plane, and the FIB is derived from the RIB. E. The FIB is derived from the control plane, and the RIB is derived from the FIB.

Which function does a fabric edge node perform in an SD-Access deployment? fffffffabric eeeeeeeeeeedge node perform in an SD-Access deployment eeeeeeeeeeeendpoints to the fffffffffffffabric and fffffffffffffforwards their traffffffffffffic. A. Connects endpoints to the fabric and forwards their traffic. B. Encapsulates end-user data traffic into LISP. C. Connects the SD-Access fabric to another fabric or external Layer 3 networks. D. Provides reachability between border nodes in the fabric underlay.

What is the role of a fusion router in an SD-Access solution?. A. acts as a DNS server. B. provides additional forwarding capacity to the fabric. C. performs route leaking between user-defined virtual networks and shared services.

Which action is the vSmart controller responsible for in an SD-WAN deployment? it's smart to distribute... A. onboard vEdge nodes into the SD-WAN fabric. B. gather telemetry data from vEdge routers. C. distribute security information for tunnel establishment between vEdge routers.

What is one fact about Cisco SD-Access wireless network deployments? the AP is way UP above.... A. The access point is part of the fabric overlay. B. The wireless client is part of the fabric overlay. C. The access point is part of the fabric underlay. D. The WLC is part of the fabric underlay.

Which controller is the single plane of management for Cisco SD-WAN?. A. vBond. B. vSmart. C. vManage. D. vEdge.

What is the difference between the MAC address table and TCAM?. A. TCAM is used to make L2 forwarding decisions. CAM is used to build routing tables. B. Router prefix lookups happen in CAM. MAC address table lookups happen in TCAM. C. The MAC address table supports partial matches. TCAM requires an exact match. D. The MAC address table is contained in CAM. ACL and QoS information is stored in TCAM.

A company plans to implement intent-based networking in its campus infrastructure. Which design facilitates a migration from a traditional campus design to a programmable fabric design?. A. two-tier. B. Layer 2 access. C. three-tier. D. routed access.

Which statement about a fabric access point is true? AP → edge. A. It is in local mode and must be connected directly to the fabric edge switch. B. It is in local mode and must be connected directly to the fabric border node. C. It is in FlexConnect mode and must be connected directly to the fabric border node. D. It is in FlexConnect mode and must be connected directly to the fabric edge switch.

While configuring an IOS router for HSRP with a virtual IP of 10.1.1.1, an engineer sees this log message. Jan 1 12:12:12.111 : %HSRP-4-DIFFVIP1: GigabitEthernet0/0 Grp 1 active routers virtual IP address 10.1.1.1 is different to the locally configured address 10.1.1.25 Which configuration change must the engineer make? DIFFERENT TO THE LOCALLY CONFIGURED........... A. Change the HSRP group configuration on the local router to 1. B. Change the HSRP virtual address on the local router to 10.1.1.1. C. Change the HSRP virtual address on the remote router to 10.1.1.1. D. Change the HSRP group configuration on the remote router to 1.

A network administrator has designed a network with two multilayer switches on the distribution layer, which act as default gateways for the end hosts. Which two technologies allow every end host in a VLAN to use both gateways? (Choose two.). A. VRRP. B. GLBP. C. VSS. D. MHSRP. E. HSRP.

Under which network conditions is an outbound QoS policy that is applied on a router WAN interface most beneficial? the police hates the saturated. A. under traffic classification and marking conditions. B. under interface saturation conditions. C. under all network conditions. D. under network convergence conditions.

What is the function of a fabric border node in a Cisco SD-Access environment? border node → connect connect connect connect. A. To collect traffic flow information toward external networks. B. To connect the Cisco SD-Access fabric to another fabric or external Layer 3 networks.

In a wireless Cisco SD-Access deployment, which roaming method is used when a user moves from one AP to another on a different access switch using a single WLC?. A. Layer 3. B. inter-xTR. C. auto anchor. D. fast roam.