Modulo 3 - 4. MAINTAIN SEAWORTHINESS- SHIP CONSTRUCTION C

What stresses are the vessel's structure forward of the collision bulkhead stiffened to resist?. Panting & Pounding. Panting & Racking. Water Pressure. Hogging & Sagging.

What is the uppermost continuous hull plating called?. Sheer Strake. Garboard Strake. Stealer Plate. Stringer Plate.

A perforated flat is part of the structure in the....... forward hold. double bottom. deck house. fore peak.

How are stacked containers prevented from moving in the hold?. By girders. By wire lashings. By portable beams. By cell guides.

What are bulkhead stiffeners attached to the tank top by?. Cleats. Brackets. Stays. Chocks.

What is a keel structure constructed to allow piping to run through called?. Bar Keel. Flat Plate Keel. Box Keel. Duct Keel.

What is the type of rudder shown in the figure?. Unbalanced. Semi-balanced. Balanced. Spade.

What is the connecting plate between a side frame and a transverse deck beam called?. Bracket. Gusset. Knee. Stiffener.

Gross tonnage is defined as.... learning capacity. internal capacity. light displacement. load displacement.

What is distortion of a vessel's structure caused by rolling called?. Racking. Slamming. Pounding. Heaving.

The lower end of the stem bar of a ship is attached to ...... stringer. frame. beam. keel plate.

What is the pipe which directs the anchor cable from the windlass to the chain locker called?. Mooring. Hawser. Spurling. Scupper.

What is the item shown in the figure?. Stay. Strut. Bulwark Stanchion. Stiffener.

What is a vertically welded shell joint called?. Butt. Lap. Seam. Joint.

What stress is the connection of frames and beams at deck level between the bulkheads designed to resist?. Hogging. Sagging. Racking. Pounding.

Racking stresses in a ship can be reduced by fitting a good system of...... stringers. deck girders. side girders. bulkheads.

What is the minimum number of transverse bulkheads required for a vessel with machinery aft?. Three. Four. Five. Six.

A General Arrangement drawing gives details of a vessel's.... construction sequenc. tank capacities. hydrostatic information. layout.

What is the type of framing shown in the ship cross section?. Transverse. Longitudinal. Combination. Web.

Additional bottom stiffening is required immediately aft side of the collision bulkhead to resist....... racking. panting. pounding. hogging.

When a vessel is hogging the keel will be i...... sheer. tension. torsion. compression.

What is the type of weld shown in the figure?. Fillet. Butt. Vee Butt. Lap.

In the figure, what is the section marked 4 called?. Flat Bar. Tee. Angle. Offset Bulb.

What could the steel section shown in the figure be used to construct?. Tank Top. Hatch Cover. Bulkhead. Steering Flat.

In the figure, what are the items marked 6 called?. Chocks. Bilge Brackets. Knees. Webs.

In ideal conditions, the forward distance a propeller will move in one revolution of the shaft is the: Diameter. pitch. slip. circumference.

Where is the top of a stern frame connected to a vessel's structure?. After Peak Bulkhead. Steering Flat. Transom Floor. Vibration Post.

What is the item of structure numbered 12 in the figure called?. Boss Plate. Stern Bearing. Stern Post. Stern Frame.

What is the item of structure numbered 9 in the figure?. Deck Plate. Panting Stringer. Foundation Plate. Floor Plate.

What is a drawing used to identify individual strakes and plates called?. Construction Drawing. Sheer Profile. Shell Expansion Plan. Body Plan.

Water is drained from an exposed deck by....... discharge pipes. side scuttles. freeing ports. drain valves.

The vertical distance measured from the deck line to the centre of the load line disc is the....... depth. winter draught. summer draught. statutory freeboard.

What is the vertical distance top to top between the load line marks S and F?. Summer Allowance. Tropical Allowance. Dock Water Allowance. Fresh Water Allowance.

Moulded beam is the measurement taken to the....... inside of the plating. outside of the plating. inside of the frames. inside of the ceiling.

What is the item of structure numbered 11 in the figure called?. Bulkhead. Floor Plate. Wash Plate. Web.

What is the item of structure numbered 10 in the figure called?. Breast Hook. Diamond Plate. Bracket. Bow Chock.

What is the hinge on which a rudder turns called?. Bolt. Pin. Gudgeon. Coupling.

What is the weight a vessel can carry called?. Load Displacement. Gross Tonnage. Registered Tonnage. Deadweight.

What is the condition in which the greatest pounding stresses in a ship are liable to occur?. Loaded, beam sea. In ballast, beam sea. Loaded, head sea. In ballast, head sea.

Where are panting stresses for a ship most severe?. Forward. Amidships. Aft. Between the bulkheads.

A vessel in the condition shown in Figure will be.... hogging. sagging. racking. twisting.

What is the transverse curve of the deck called?. Flare. Rake. Camber. Tumblehome.

What is the athwartships cross section structure shown in the figure2?. Box Keel. Bar Keel. Flat Plate Keel. Duct Keel.

What is the longitudinal curve of the deck called?. Sheer. Freeboard. Rise of Floor. Rake.

To prevent water entering the space below, door openings on the weather deck should be constructed with approved..... drains. sills. scuppers. baffles.