NS0-162

1. You currently have an 8-node cluster and want to perform a rolling upgrade to a newer version of ONTAP to solve security issues reported in the Active IQ Web site. In this scenario, which two steps should you validate before you perform the upgrade? (Choose two.). Run Active IQ Config Advisor. Validate Nodes with Hardware Universe. Validate Nodes with Active IQ Unified Manager. Run Upgrade Advisor Report.

When performing a manual MetroCluster switchover, which two statements are true? (Choose two.). Only the user specified DR groups are switched over. All SVMs in the disaster site are switched over. All DR groups in the disaster site are switched over. Only the user specified SVMs are switched over.

A volume is only 25% full; however, the snapshot reserve is almost full. Referring to the exhibit, what occurs after the volume's snapshot reserve is full?. User-created Snapshot copies are deleted, beginning with the oldest, until the snapshot reserve has 20% free space. Scheduled Snapshot copies are deleted, beginning with the oldest, until the snapshot reserve has 20% free space. Snapshot copies start consuming the volume's free space. The creation of new Snapshot copies fails.

Which two statements about replicating FlexGroup volumes are true? (Choose two.). You can increase the capacity of a FlexGroup volume that is being replicated. The SnapMirror relationship type must be XDP. You cannot perform a resync on a FlexGroup SnapMirror relationship after it has been broken. The SnapMirror relationship type must be DP.

What are two advantages of creating small RAID groups inside an aggregate? (Choose two.). maximized storage space. decreased risk of multiple disk failure. shorter reconstruction time. additional available spare drives.

While troubleshooting performance issues, you notice that only one port in the NetApp interface group a0a is actively sending or receiving data. Referring to the exhibit, what should you do to ensure that both ports in the interface group are actively used?. Change the interface group mode to multimode_lacp. Verify that the network switch has flow-control enabled. Verify that the physical cabling is properly connected to ensure a network link. Change the distribution function to ip.

When a write from a SAN host is received, the information is stored within the controller before it is written to the underlying RAID. In this scenario, which component stores the data?. NVRAM. Flash Pool. HBA. FlashCache.

Which two features are supported on NetApp ONTAP? (Choose two.). SnapMirror. FlexCache. Fibre Channel. Storage Pool.

You created a new SVM with two NFS data volumes. You have a Linux host on the same subnet as the SVM that is able to NFS mount, however a Linux host on a different subnet is not able to NFS mount. You confirmed that the export policy rules are correct. In this scenario, which configuration will solve the mount failure? (Choose the best answer.). The NFS server is not configured on the SVM. NTP is not configured on the SVM. NFS auditing is not enabled on the SVM. The SVM default network route is missing.

Which ONTAP feature uses the Service Processor to speed up takeover times between HA pairs?. hardware-assisted takeover. automatic takeover and giveback. epsilon. cluster HA.

Node A has taken over Node B. You solved the issue that caused the takeover and are now ready to resume normal operation. After initiating the storage failover giveback command, how are the aggregates given back? (Choose the best answer.). CFO aggregates are automatically given back, SFO aggregates must be manually given back. CFO aggregates and SFO aggregates are automatically given back. The root aggregate is automatically given back, CFO and SFO aggregates must be manually given back. SFO aggregates are automatically given back, CFO aggregates must be manually given back.

You need to move a FlexVol volume from one SVM to another. In this situation, which command would accomplish this task?. volume create. volume rehost. volume modify. volume move.

Which three name services are supported with NFS? (Choose three.). NetBIOS. WINS. External NIS domains (NIS). External LDAP domains (LDAP). Local Users (file).

On your customer's AFF A700, there are multiple volumes within the aggregate aggr1. Within aggr1, volumes vol1, vol2, and vol3 store similar data, and volumes vol4 and vol5 store unique data. In this scenario, which feature would improve storage efficiency with the data stored in volumes vol1, vol2, and vol3?. postprocess compression. data compaction. inline aggregate-level deduplication. inline compression.

Which three steps are required to serve NFS exports from your ONTAP system? (Choose three.). You must create an export policy rule. You must license CIFS. You must create an SMB share. You must license NFS. You must have provisioned a volume to export.

You have a 2-node ONTAP cluster with both 0e ports connected to Fabric A. You have an FC host connected to the FC fabric with the following initiator WWNs: - WWNN: 20:00:00:25:B5:01:F0:2A - WWPN Fabric A: 20:00:00:25:B5:01:A0:2A Referring to the exhibit, which three WWNs should be configured in a zone together? (Choose three.). 20:0d:00:a0:98:69:97:ff. 20:00:00:25:B5:01:F0:2A. 20:0f:00:a0:98:69:97:ff. 50:0a:09:82:80:01:b7:1b. 20:00:00:25:B5:01:A0:2A.

An administrator is designing an ONTAP solution that consists of eight FAS8200 nodes in a single cluster. Each node will use four ports for cluster connections. Which cluster interconnect switch model should be used in this scenario?. Nexus 5596UP. Nexus 5010. CN1610. CN1601.

Which two statements are true when you restore a volume from a Snapshot copy? (Choose two.). All Snapshot copies that were created after the Snapshot copy was created are lost. All data that was written to the volume after the Snapshot copy was created is lost. The volume’s SnapMirror relationships need to be re-created. After the volume is restored, it becomes read-only.

You execute the cluster1::> network ipspace showcommand, and notice that two IPspaces are not able to be renamed or deleted. Referring to the exhibit, what are these two IPspaces? (Choose two.). A. IPspace2. B. Default. C. IPspace1. D. Cluster.

An SVM is configured to authenticate SVM administrators with the access method set to Password. A computer account for the SVM exists on the Active Directory domain controller. You are now required to authenticate administrators through domain. Which two steps are required to accomplish this task? (Choose two.). Re-create the computer account for the SVM on the domain. Configure the SVM as a tunnel to the domain. Create a custom role for all users who belong to the domain. Create a login account on the cluster for the domain users with an access method of 'domain'.

In which scenario would you specifically assign aggregates to SVMs?. to configure an ONTAP system for CIFS and iSCSI. to create SnapMirror peering relationships between SVMs. to prevent a storage administrator from overcommitting an aggregate. to configure an ONTAP system for multi-tenancy.

A storage administrator currently has an 8-node FAS8200 cluster with CIFS, NFS, and iSCSI licenses installed. In this scenario, how many additional nodes are supported?. 3. 6. 4. 1.

An administrator has an SVM named SVM_NAS that is used for NFS clients. You change the volume junction path of a volume named vol1 from /vol1 to /IT/vol1. After you make this change, the existing NFS clients are unable to connect to the new path. Which cluster object should you update to solve this problem?. the load-sharing mirror of the SVM root volume. the cluster admin LIF. the data LIF on the SVM_NAS SVM. the export policy on the SVM_NAS SVM.

You want to improve the write performance of NL-SAS volumes serving data on your ONTAP. You also want to keep the performance consistent during a possible controller failover. In this scenario, which feature do you use? (Choose the best answer.). Flash Cache. Flash Pool. FlexCache. FabricPool.

You must expand an existing FAS8200 switchless cluster to a switched cluster and add a new FAS8200 HA pair in the cluster. In this scenario, which three actions would you perform to expand the cluster? (Choose three.). Ensure that the switchless-cluster network option is false. Connect the existing nodes to the cluster switches. Change the cluster ports for the existing HA pair. Ensure that the switchless-cluster network option is true. Join the new HA pair to the cluster.

Which block protocol does ONTAP Cloud support?. iSCSI. FCoE. CIFS. NFS.

When FCOE is used in a cluster, which feature must be licensed?. CIFS. NFS. iSCS1. FCP.

You are training a storage operator to view the aggregates available on the nodes from multiple shells. Which two shell and command combinations would you use to accomplish this task? (Choose two.). nodeshell aggregate status. systemshell aggregate status. systemshell aggregate show. clustershell aggregate show.

Which type of write once, read many (WORM) workload is designed for compliance purposes through SnapLock?. WORM files on MetroCluster volumes. WORM files on SyncMirror aggregates. WORM files using SnapMirror replication. WORM files on FlexArray aggregates.

Your company has recently decided to stop using the Fibre Channel Protocol (FCP) in the data center. You are asked to decommission FCP and reuse any UTA2 ports to 10 GbE. Which two steps are involved in this task? (Choose two.). Reboot the nodes. Destroy any FC LIFs hosted on UTA2 ports. Remove the FCP license from all nodes in the cluster. License additional ports for 10 GbE connectivity.

An administrator wants to segment applications based on performance. The applications are all using LUNs to access their data. In this scenario, what are two methods of using quality of service (QoS) to improve performance? (Choose two.). Set the policy group for the SVM that is hosting the LUNs. Set the policy group for the volumes that are hosting the LUNs. Set the policy group for the initiator groups (igroups) mapped to the LUNs. Set the policy group for the FC target ports that are being used for the LUNs.

You execute the volume unmount -vserver vsl -volume vol1 command. In this scenario, which statement is true?. Data within the vol1 volume is lost. All data within the junction point is inaccessible to NAS clients. The Snapshot policy in the volume needs to be recreated once the volume is remounted. The existing volume export policies and SMB shares created on the volume or on directories and junction points within the unmounted volume are not retained.

Which configuration is supported by MetroCluster?. a single AFF at Site A attached through fabrics to an AFF HA pair at Site B. an AFF HA pair at Site A attached through fabrics to a FAS HA pair at Site B. a single AFF at Site A attached directly to a single AFF at Site B. an HA pair at Site A attached directly to an HA pair at Site B.

34. An administrator wants to restore a file using the Previous Versions tab on a Windows client. Which command enables the Previous Versions feature?. volume modify -group. volume modify -user. volume modify -policy. volume modify -snapdir-access.

An administrator needs to configure ports for peering. Referring to the exhibit, which ports should be used?. CDOT93-01:e0a and CDOT93-02:e0a. CDOT93-01:e0e and CDOT93-02:e0e. CDOT93-01:e0d and CDOT93-02:e0d. CDOT93-01:e0f and CDOT93-02:e0f.

When a storage QoS policy is configured, which two metrics are configured with a maximum limit? (Choose two.). concurrent connections. IOPS. MBps. latency.

Which command would you use to enable the ONTAP HA feature?. storage failover modify -enabled true -node *. cluster ha modify -configured true. cluster ha modify –configured false. network options switchless-cluster modify true.

How would you protect a NAS SVM root volume?. Create a SnapMirror copy of the root volume to a peer cluster. Create load-sharing mirrors. Create a backup the SVM configuration. Create a backup of the SVM root volume.

You have Windows Server 2019 hosts that use network address translation (NAT) on the network when connecting to their ONTAP 9.8 AFF A400 cluster. You are having iSCSI connectivity issues using IP addresses. The network team recommends using fully qualified domain names (FQDNs). Which SAN setting in ONTAP would you modify in this scenario?. LIF service policies. Selective LUN Map (SLM). SendTargets. port sets.

You have a mission-critical SQL application that uses a single SMB 3.1.1 share to host its database. The storage node that is hosting the SMB share sql01_ca for the SQL database experiences a hardware failure and fails over to the surviving node. Referring to the exhibit, what is the state of the SMB share for the SQL database during the failover? (Choose the best answer.). The SMB share will be available, but all data is corrupted. The SMB share will be unavailable until node failback. The SMB share will be available, and all data is accessible. The SMB share is unavailable due to its stateful nature.

Which commands shows the data compaction savings for an aggregate?. storage aggregate show-space. storage aggregate show-efficiency. volume efficiency show. storage efficiency show.

Referring to the exhibit, a customer is experiencing performance problems on an SVM supporting NVMe/FC. You review the physical FC ports that are connected into the 32 Gbps switches for cluster tme-a700. In this scenario, what is causing the performance problems? (Choose the best answer.). Port 2a needs more network interfaces added to the physical port. Port 2b has a 16 Gbps SFP+ installed. Port 2a needs a 16 Gbps SFP+ installed. Port 2b has two many LIFs running across the physical port.

A storage administrator has an existing FAS2554 HA pair. They want to add a new FAS2620 HA pair to the cluster. The SAN protocols are licensed.Referring to the exhibit, after adding the second HA pair, how many more nodes are available to add for future use?. 4. 8. 2. 12.

Which two components are required for committing data to a WORM volume? (Choose two.). You must license SnapLock. You must create a SnapLock volume. You must create a SnapLock SVM. You must create a SnapLock Aggregate.

Your manager asks you to create a new FlexVol on an aggregate called AGGR_2. When you click "Create new FlexVol", you are unable to select AGGR_2 to create the new volume. Referring to the exhibit, which two SVM settings solve this problem? (Choose two.). In the resource allocation tab, select the "Delegate volume creation" option and select AGGR_2. Use the volume move option and reallocate the SVMs root volume to AGGR_2. In the resource allocation tab, select the "Do not delegate volume creation" option. Change the aggregate security style of AGGR_2 to UNIX.

You change a volume's space guarantee from volume to none. In this scenario, which statement is correct?. Free space from the volume shows up as free space in the aggregate. All existing snapshots are automatically deleted. Snap reserve is set to zero (0). Fractional reserve is set to zero (0).

A storage administrator is unable to mount NFS volumes in the SVM1 namespace. Referring to the exhibit, what is causing this problem?. The NFS v4 ACL support is disabled. The NFS protocol is disabled. The NFS license is disabled. The NFS v3 and v4 protocols are running at the same time.

The maximum RAID group size of the RAID-DP aggr1 shown in the exhibit is 18. You expand the aggregate by 20 disks. How many of the new disks are used for data?. 20. 16. 14. 18.

You are provisioning a LUN for a new host. In this scenario, which three objects must exist? (Choose three.). export policy. igroup. LUN. interface group. volume.

Which NetApp cluster configuration requires the use of epsilon?. a singe-node cluster. a cluster with an odd number of nodes. a 2-node cluster. a 4-node cluster.

Which three configurations does ONTAP Select support? (Choose three.). 2-node cluster hosting NAS and iSCSI. 3-node cluster hosting NAS and iSCSI. single-node cluster hosting NAS and iSCSI. 4-node cluster hosting NAS and iSCSI. 6-node cluster hosting NAS and iSCSI.

What are three types of licenses available for ONTAP? (Choose three.). standard. evaluation. system. site. field.

An administrator is configuring a third-party software for NDMP. The application is targeting the IP of the data LIF of the SVM called "SVM1. "NDMP is configured as the SVM scope. The NDMP service is not enabled for the admin SVM. SVM1 has a user called "Tom" with the backup role. Tom can connect by using SSH to the controller with the credentials that he used to configure the third-party software. The authentication of the third-party software is falling. In this scenario, what is the reason for the authentication failure?. The NDMP password has not been generated for Tom. The application is not targeting the IP of the cluster or node management LIF. The user Tom does not belong to the admin SVM. The NDMP service is not enabled for the admin SVM.

You want to use UTA2 ports for native FC LUN access. How do you accomplish this task?. Configure the UTA2 ports as target ports with 16 Gb SFP+ transceivers. Configure the UTA2 ports as target ports with 10 Gb SFP+ transceivers. Configure the UTA2 ports as initiator ports with 10 Gb SFP+ transceivers. Configure the UTA2 ports as initiator ports with 16 Gb SFP+ transceivers.

Which two types of HA policies are applied to which types of aggregates? (Choose two.). storage failover (SFO) policy to data aggregates only. controller failover (CFO) policy to all the aggregates. storage failover (SFO) policy to root aggregates only. controller failover (CFO) policy to root aggregates.

When you create a FlexVol volume, which security style is applied by default?. the security style of the SVM root volume. the security style of the root volume of the cluster. NTFS. UNIX.

An administrator is configuring an aggregate to use FabricPool to take advantage of auto tiering. In this scenario, what are three requirements to accomplish this task? (Choose three.). volume with space-guarantee none. FabricPool license. intercluster LIFs. volume with space-guarantee volume. AFF array.

Which three name services does ONTAP support? (Choose three.). HTTP. local files. LDAP. NIS. SNMP.

Which NetApp software do you use to confirm that the SAS cabling is correct?. Hardware Universe. Active IQ Config Advisor. Interoperability Matrix Tool. Active IQ Unifide manager.

You have a mix of FAS8200s and AFF A700s in your environment. In this scenario, which two statements are true? (Choose two.). Inline data compaction is disabled by default on FAS systems. Inline aggregate-level deduplication is enabled by default on FAS systems. Inline data compaction is disabled by default on AFF systems. Inline aggregate-level deduplication is enabled by default on AFF systems.

Which mediator type is required for an ONTAP Select 2-node HA solution?. mediator code. mediator storage virtual machine. mediator cluster. mediator virtual machine.

Assuming that the export policy on the storage allows access, you want to enable client access to the finance volume in the departments SVM in the /tmp/fin directory. Referring to the exhibit, which UNIX command must be executed to accomplish this task?. mount –t nfs –o nfsvers=3 cluster01:/finance /tmp/fin. mount –t nfs –o nfsvers=3 cluster01:/fin /tmp/fin. mount –t nfs –o nfsvers=3 cluster01:/dept/fin /tmp/fin. mount –t nfs –o nfsvers=3 cluster01:/departments/finance /tmp/fin.

Which two statements are true about epsilon? (Choose two.). Epsilon is automatically assigned to the last node when the cluster is created. Epsilon is an extra fractional vote that enables quorum. In a two-node cluster, each node holds epsilon. Epsilon is automatically assigned to the first node when the cluster is created.

A storage administrator moves a LUN from one volume to another. In this scenario, what is left behind in the volume?. LUN geometry settings. all of the deduplicated blocks from the base LUN. Snapshot copies of the volume. clones of the LUN.

An export policy rule for a volume is set by using the command shown in the exhibit. If clients with IP addresses 10.64.19.0 and 10.64.18.20 accessed the export, what is the outcome?. Neither client is given access. Client 10.64.19.0 is given access but 10.64.18.20 is not given access. Client 10.64.19.0 is not given access but 10.64.18.20 is given access. Both clients are given access.

Your company requires that all data must be encrypted in flight to prevent data from falling into the wrong hands.What are two ways to accomplish this task? (Choose two.). Ensure that SnapMirror compression is enabled in all SnapMirror relationships. Modify your cluster peering relationships to support cluster peering encryption. Enable Multi-Factor Authentication (MFA) for your SnapMirror relationships. Ensure that all intercluster replication traffic is done through a VPN tunnel.

On which two types of ports would data LIFs be hosted? (Choose two.). physical ports or interface groups that host VLANs. management e0M port. console RJ45 port. physical ports that are not part of interface groups.

You are an administrator that manages a number of mission-critical applications that use block protocols only. The business unit requires the fastest storage failover. In this scenario, which ONTAP solution satisfies the requirement?. All SAN Array (ASA) with symmetric active-active topology. ONTAP Select with Asymmetric Logical Unit Access (ALUA). AFF with Asymmetric Logical Unit Access (ALUA). FAS with symmetric active-active topology.

You relocate an aggregate to a different node by using the storage aggregate relocate command. In this scenario, which rule applies?. You cannot relocate an aggregate that is hosting a FlexGroup constituent volume. You can only relocate an aggregate to the HA partner node. You can only relocate an aggregate that is not assigned to a specific SVM. You must first break the relationship to move an aggregate that hosts a replication destination.

Which three statements are true for mailbox disks per node in an HA pair? (Choose three.). Six disks are required if the root volume is on a mirrored aggregate. Two disks are required if the root volume is on a disk shelf. Four disks are required if the root volume is on a mirrored aggregate. Eight disks are required if the root volume is on partitioned disks. One array LUN is required if the root volume is on a storage array.

What is the purpose of Epsilon?. to monitor cluster health. to be used as a load-balancer for a 2-node cluster. to evaluate the differences in node configurations. to be used as a tie-breaker for a cluster quorum.

Which two licensed protocols are assigned to an SVM for block protocols? (Choose two.). FCoE. FCP. CIFS. iSCSI.

To configure high availability within a FAS8080 EX HA pair, which two statements are correct? (Choose two.). Connect the NVRAM HA interconnects between the nodes in the HA pair. Cable the cluster interconnects to the interconnect switch. Connect multiple FC paths from the controllers to the hosts. Connect both the local node and partner node to disk shelves using multipath HA.

You are the administrator of your company's ONTAP 9.7 storage system. Your system hosted CIFS shares in your Active Directory environment for several years without any problems. Suddenly users report to you that they can no longer access their CIFS shares. What is the reason for this problem? (Choose the best answer.). The CIFS standard license expired. The user account used to join your SMB server to your Active Directory expired. The WINS servers are unreachable. The NTP servers are unreachable.

Referring to the exhibit, what is a valid storage failover scenario?. Node 1 fails and Node 2 takes over Node 1's storage. Node 4 fails and Node 2 takes over Node 4's storage. Node 3 fails and Node 1 takes over Node 3's storage. Node 2 fails and Node 3 takes over Node 2's storage.

Your 4-node cluster has two controllers in takeover as shown in the exhibit. Which action must be performed to ensure a giveback occurs on both nodes?. Perform a giveback of node4. Perform a giveback of node3. Perform a giveback of node2. Perform a giveback of node1.

Which two objects are supported in a FlexVol volume? (Choose two.). aggregate. qtree. RAID group. LUN.

You are working on a disaster recovery situation where the controller, which is part of a fabric-attached MetroCluster configuration in the disaster site, fails to boot and stays at the loader prompt. This failure generates the error message that is shown in the exhibit. Which sequence of steps will recover the disaster site?. Perform switchback, heal data aggregate, heal root aggregate, and boot ONTAP. Heal root aggregate, heal data aggregate, boot ONTAP, and perform switchback. Heal data aggregate, heal root aggregate, boot ONTAP, and perform switchback. Boot ONTAP, heal root aggregate, heal data aggregate, and perform switchback.

Referring to the exhibit, what are two reasons why no initiators are displayed in the initiators' igroup screen? (Choose two.). The server has not been powered up. SLM has not been enabled. Zoning on the switches has been done incorrectly. ALUA has not been enabled on the NetApp controllers.

You have a FAS8200 serving a dataset with a high volume of random reads. The dataset is highly optimized by deduplication and compression. In this scenario, which compression setting provides both high performance and storage efficiency? (Choose the best answer.). compression disabled. aggregate compression. secondary compression. adaptive compression.

Referring to the exhibit, which connections are used for the cluster interconnect LIFs?. 1. 2. 3A. 3B.

You are setting up replication between two clusters. In this scenario, which two components are required to set up the cluster peering? (Choose two.). DNS service on each cluster. An intercluster LIF on only the epsilon node. ICMP service between clusters. An intercluster LIF on every node.

When a cluster is created, which two objects are required to provide management access? (Choose two.). data LIFs. management LIFs. data SVM. admin SVM.

An administrator notices that the applications are running slowly. The administrator wants to determine which component on the ONTAP subsystem is experiencing the most latency. In this scenario, which command would you use to accomplish this task?. run -node * stats show system::sys_avg_latency. statistics system show. run -node * -command sysstat -x 1. qos statistics latency show.

You have a FAS8200 HA pair with disks that are evenly split between nodes A and B. When a disk fails, the replacement disk must automatically assign back to the originally assigned controller, A or B. Referring to the exhibit, which disk auto assign policy satisfies this requirement?. stack. bay. default. shelf.

Your ONTAP cluster serves data and backup traffic running on the same physical port. You must isolate backup traffic from your production network traffic. Which two actions must be performed to accomplish this task? (Choose two.). Create a namespace. Create a VLAN. Create a broadcast domain. Create IPspaces.

At which level of granularity would you back up data to tape using the SMTape command?. directory. qtree. volume. aggregate.

You have a RAID-DP aggregate with 42x 4 TB NL-SAS drives. The aggregate contains 3x RAID groups of 14 drives each (12 data + 2 parity), for a total of 36 data and 6 parity drives.You decide to convert the aggregate to RAID-TEC for higher resiliency. How many spare 4 TB drives are needed to complete the conversion?. 1. 2. 4. 3.

Which failover policy is set by default on an iSCSI LIF?. local-only. broadcast-domain-wide. disabled. sfo-partner-only.

You have a 4-node NetApp SAN cluster configured as shown in the exhibit. By default, how many LUN paths does the host see for a newly created LUN on Node 01?. 2. 1. 8. 4.

Which three data protocols are supported simultaneously in a single storage virtual machine (SVM)? (Choose three.). FCP. iSCSI. HTTP. CIFS. InfiniBand.

You have an AFF A300 2-node cluster and are adding a FAS8200 to this cluster for additional storage capacity. You want to move a volume to one of the FAS8200 nodes. Which ONTAP command is used to accomplish this task?. volume aggr vacate. volume rehost. volume move. aggr relocate.

You have a test SVM named svm1 with a LIF that needs to reach a DNS server on a different Layer 2 network. The default route for each network ends in .1 and both networks route to each other. Referring to the network command output shown in the exhibit, which command will allow access from svm1 to lab.local DNS?. network route create -vserver svml -destination 192.168.0.0/24 -gateway 192.168.2.1 -metric 20. network route create -vserver svml -destination 0.0.0.0/0 -gateway 192.168.2.1 -metric 20. network route create -vserver svml -destination 0.0.0.0/0 -gateway 192.168.0.1 -metric 20. network route create -vserver svml -destination 192.168.0.0/24 -gateway 192.168.0.1 -metric 20.

The exhibit displays the values for the default adaptive QoS policy. An administrator assigns the Value policy to a 1 TB volume. Over time, the volume expands to 3 TB. What is the peak IOPS for the volume, both before and after the expansion? (Choose the best answer.). 512 IOPS and 512 IOPS. 512 IOPS and 1536 IOPS. 512 IOPS and 12288 IOPS. 75 IOPS and 512 IOPS.

You want to prevent a single file from filling up a single constituent in a FlexGroup. Which FlexGroup feature in ONTAP 9.7 will accomplish this task? (Choose the best answer.). Flash Pool. fractional reserve. Snapshot autodelete. elastic sizing.

A customer has lost access to shares being used by an application. What are three troubleshooting steps the administrator should take? (Choose three.). Verify that the admin SVM is running on the node being accessed by the customer. Verify that the LIF resides on its home port. Verify that the LIFs in the SVM are all up and active. Verify that the SVM has CIFS running, that the share exists, and is online. Verify that there is network connectivity between the SMB client and the SVM.

You need to create a 200 GB volume that requires 700 IOPS. Referring to the exhibit, in which aggregate should you create the volume?. aggr1_01. aggr2_02. aggr1_02. aggr2_01.

A customer wants to add nodes to an 8-node AFF A700 NAS cluster. In this scenario, what is the maximum number of additional nodes?. 8. 16. 24. 12.

Regarding root partitioned disks in an ONTAP system, which three types of objects are associated with ADP? (Choose three.). root partition. array LUN. data partition. shared disk. container disk.

cluster1::> volume create -vserver vsl -volume voll -aggregate aggr1 -encrypt true Which statement regarding the command shown in the exhibit is true?. The volume will be created and protected on an aggregate using NetApp Storage Encryption (NSE) disks. The volume will be created and protected using an external Key Management Server. The volume will be created and protected for Snaplock Enterprise compliance. The volume will be created and protected using NetApp Volume Encryption (NVE).

You create a quality of service (QoS) policy group called untest_apps with a maximum throughput of 300 MBPS. You add one volume to the policy group, and then you add a second volume to the policy group.In this scenario, which statement is true?. The combined maximum throughput of both volumes is 600 MBPS. The maximum throughput of each volume is 150 MBPS. The maximum throughput of each volume is 600 MBPS. The combined maximum throughput of both volumes is 300 MBPS.

Which two SVM types does a cluster contain after cluster creation? (Choose two.). dp-destination. peer. data. admin.

You must create a CIFS share for a replicated destination volume for read-only access to the files. In this scenario, which task must be completed before you create the share?. Mount the volume. Break the replication. Change permissions. Set up the preferred domain controller.

You have a Windows 10 computer that lost an SMB drive mapping that used the IP address of your SVM. The mapping was working until security requirements disabled NTLM authentication. Windows Server 2019 servers remained connected to the drive mapping. The cluster clock is incorrect by more than 3 minutes. Kerberos requires the server name. DNS is not enabled. SMBv3 is required.

You have a FlexClone parent volume with several child volumes. In this scenario, which statement is true when you move the FlexClone parent volume to another aggregate? (Choose the best answer.). All FlexClone child volumes are also moved. All FlexClone child volumes are split and are no longer FlexClone volumes. The volumes move operation fails. A temporary FlexClone parent remains on the original aggregate.

You have a 2-node NetApp cluster with CIFS volumes and SAN LUNs on both nodes. The FC hosts have MPIO correctly configured and see LUN paths through both NetApp nodes. During a node failover, which two statements are true? (Choose two.). FC hosts will experience an outage. FC hosts will not experience an outage. Some CIFS users may experience a brief outage. CIFS users will not experience any outage.

Your customer has an NTFS volume that they want to access over both SMB and NFS. The client explains that SMB access works fine, but the clients are unable to NFS mount the volume.What are three reasons that would cause this issue? (Choose three.). There is no export-policy rule for the NFS clients. The NSF server is not configured. Multi-protocol is not licensed on the cluster. The volume security style must be changed to UNIX. The LIF data protocol does not allow NFS.

You have an ONTAP 9.7 cluster. You increased the size of the volume to 3 TB, but the IOPS did not increase as expected. What are the expected IOPS for the volume after the change? (Choose the best answer). 2048. 6144. 1024. 4096.

A customer has a new ASA platform but cannot get the target FC ports to show up in ONTAP System Manager. Referring to the exhibit, what would cause this problem?. The FC license is unlicensed. The base license is enabled. The FabricPool license is unlicensed. The SMB/CIFS license is unlicensed.

Which privilege is assigned to the vsadmin-backup role?. configuring SnapMirror relationships between clusters. managing Snapshot copies. managing volumes. configuring LIFs for cluster peering.

Referring to the exhibit, you have a FlexGroup volume that is 250 TB with 10 constituents. You apply the volume modify –vserver fg1_vs –volume fg1 –size 350TB command. What affect does the command have on the FlexGroup volume and its constituents?. It grows the FlexGroup volume to 600 TB by adding 14 new constituents. It grows the FlexGroup volume to 350 TB by adding four new constituent. It grows the FlexGroup volume to 350 TB by increasing the size of each constituent to 35 TB. It grows the FlexGroup volume to 600 TB by increasing the size of each constituent to 60 TB.

You created a thick-provisioned NAS volume. You receive an alert that the snapshot reserve is full. In this scenario, which two actions will solve this problem? (Choose two.). Increase the snapshot reserve percentage. Delete Snapshot copies. Decrease the volume size. Increase the fractional reserve.

You want to enable jumbo frames on a NetApp storage system. Which network object would you modify to accomplish this task?. broadcast domain. port. LIF. VLAN.

You create a Snapshot copy of a new volume. Which activity increases the size of the new Snapshot copy?. deleting data that was written to the volume before the Snapshot copy was created. deleting data that was written to the volume after the Snapshot copy was created. reading data that was written to the volume before the Snapshot copy was created. writing new data to the volume after the Snapshot copy was created.

Referring to the exhibit, which volume has a snap reserve value set to zero (0)? (Choose the best answer.). netapp_esx_m1. netapp_esx. netapp_lnx_m1. netapp_n01.

When you create a new SSD storage pool for use with Flash Pools, how many allocation units are assigned to each node in the HA pair by default?. 8. 2. 1. 4.

An administrator has a FlexGroup volume configured on a 4-node FAS8200 cluster. New nodes have been added to the cluster, and the administrator wants to improve performance on the FlexGroup volume using the new nodes. Additionally, the FlexGroup volume size needs to increase to accommodate new workloads. Which command would satisfy the requirements in the scenario?. aggregate add-disks. volume expand. volume modify. volume mount.

Which NetApp tool indicates whether you have applied data protection policies to all volumes?. Virtual Storage Console. OnCommand Unified Manager. Config Advisor. OnCommand Service Level Manager.

You want to establish a SnapMirror relationship between two clusters. In this scenario, which two actions must you perform to accomplish this task? (Choose two.). Peer the nodes. Peer the volumes. Peer the clusters. Peer the SVMs.

In which two scenarios would you use a storage pool? (Choose two.). when providing an SSD caching layer evenly across multiple aggregates. when you need to share an SSD caching layer within an HA pair. when you have an SVM that is running a block protocol. when migrating the aggregate over to the partner node.

What are three volume-level storage efficiency features of ONTAP? (Choose three.). deswizzle. space reclamation. compaction. compression. deduplication.

You want to create a new storage pool of SSDs to provide a performance tier for FlashPool-enabled aggregates on node1 and node2. You expect that the FabricPool aggregates on node1 will require more of the performance tier than the aggregates on node2. Which action satisfies the requirement?. Use the storage disk reassign command to reassign disks from the SSD storage pool from node2 to node1. Use the storage pool reassign command to reassign storage pool allocation units from node2 to node1. Use the storage pool add command to add HDDs to the FabricPool aggregates on node1. Use the storage pool modify command to change the parity of the RAID groups in the storage pool to RAID-4.

Referring to the exhibit, how are ports e4a and e4e being used?. as 40 Gb Ethernet ports connected to a Cisco Nexus switch using native FC. as 40 Gb Ethernet ports connected through a QSFP+ to four 10 Gb Ethernet ports on a 10 Gb Ethernet switch. as 40 Gb Ethernet ports with no connection to any Ethernet switch. as 40 Gb Ethernet ports connected to a 40 Gb Ethernet switch.

You configured LACP between a 2-node AFF 220 system and two Ethernet switches using multichassis Ether-channel for redundancy. You sent the network connection diagram in the exhibit to your network team to cable and configure the switch. You noticed partial connectivity on the AFF A220 for the interface groups. Referring to the exhibit, which two statements are correct? (Choose two.). ONTAP does not have a multichassis Ether-channel feature. The network team forgot to verify the port channel members. 10 GbE ports are not supported with the AFF A220. The storage cabling to the switches is incorrect.

After you successfully deploy cluster CDOT93, you log in to System Manager and notice the error shown in the exhibit. Which command must you use to correct the error?. storage failover giveback -node CDOT93-01. storage failover modify -node * -enabled false. storage failover modify -node * -enabled true. storage failover giveback -node CDOT93-02.

You want to delete a WORM file from a SnapLock Enterprise volume. Based on this scenario, which two steps must you perform to accomplish this task? (Choose two.). Unmount the SnapLock volume from the NAS namespace. Move the file to a non-SnapLock volume. If a SnapLock audit does not exist, create one. Enable the privileged delete feature.

What are three types of shells that are used in ONTAP? (Choose three.). clustershell. systemshell. powershell. nodeshell. bashshell.

Assuming that the export policy on the storage allows access, you want to enable client access to the finance volume in the departments SVM in the /tmp/fin directory. Referring to the exhibit, which UNIX command must be executed to accomplish this task?. mount –t nfs –o nfsvers=3 cluster01:/finance /tmp/fin. mount –t nfs –o nfsvers=3 cluster01:/fin /tmp/fin. mount –t nfs –o nfsvers=3 cluster01:/dept/fin /tmp/fin. mount –t nfs –o nfsvers=3 cluster01:/departments/finance /tmp/fin.

Referring to the output shown in the exhibit, which aggregate capacity is available for a volume?. 3.4 TB. 3.6 TB. 8TB. 4TB.

A customer installed an ONTAP cluster. The customer wants to provide data access to host computers and end users. Which three tasks are required? (Choose three.). Create a Quality of Service (QoS) policy. Create an SVM. Create a LIF. Create an IPspace. Create a volume.

You are replacing a FAS system that has several DS4243 disk shelves. The new system is an AFF A300. You want to reuse the DS4243 disk shelves with your new AFF A300. In this situation, which NetApp tool would you use to confirm if the task is possible?. Active IQ. Config Advisor. Hardware Universe. Interoperability Matrix Tool (IMT).

You are configuring an FC to allow LUN access to a host system. In this scenario, a switch needs a zone configuration file that includes which two elements? (Choose two.). host initiator WWPN. SVM target WWNN. host initiator WWNN. SVM target WWPN.

You need to create a new LIF on WLAN 10. The port-channel configuration on the upstream switch has VLAN 10 set to the native (untagged) VLAN. In this scenario, what should be set as the LIF’s home port?. a0a. a0a-10. e0c-10. e0c.

You want to create a new SVM for serving NFS data using the Storage Virtual Machine (SVM) Setup wizard. In this scenario, which object is created automatically during the setup process? (Choose the best answer.). a data volume named after the SVM with the suffix _nfs_vol1. a data aggregate named after the SVM with the suffix _nfs_aggr1. a data LIF named after the SVM with the suffix _nfs_lif. an export policy named after the SVM with the suffix _nfs_exp1.

An administrator has an SVM named vs1 that is being used for UNIX workloads. Name mappings have been configured with both local name mapping files and with LDAP. NIS will not be used in the environment. The administrator needs to ensure that LDAP takes precedence for access over file-based name mappings. In this scenario, how would you accomplish this task?. Do not change anything, this is the default behavior. Use the vserver services name-service ns-switch command to set the order of preference. Modify the /etc/nsswitch.conf file to set the order of preference on the UNIX hosts connecting to the SVM. Use System Manager to modify the properties of the vserver to set the order of preference.

A network administrator has configured an upstream switch for LACP. In this scenario, which action should be performed when the NetApp interface group is created?. Set the type to “static multimode”. Set the distribution function to “port”. Set the type to “dynamic multimode”. Set the distribution function to “IP”.

You complete an installation of a FAS8200 that has two separate stacks of disk shelves. In this scenario, which NetApp tool should be used to validate the disk shelf cabling?. Config Advisor. OnCommand System Manager. OnCommand Unified Manager. Hardware Universe.

You have a new ONTAP 9.7 2-node AFF A300 cluster with 2x DS224C full shelves of 3.8 TB encrypted SSDs. In this scenario, which statement matches the factory disk-ownership setting? (Choose the best answer.). All drives on shelf 1 are assigned to one node, and all drives on shelf 2 are assigned to the partner node. All even-numbered drives on each shelf are assigned to one node, and all odd-numbered drives on each shelf are assigned to the partner node. Disk ownership is not assigned by the factory. Drives 0-11 on each shelf are assigned to one node, and drives 12-23 on each shelf are assigned to the partner node.

Which LIF types are owned by the admin SVMs? (Choose two.). Node-Management. Cluster. Data. Intercluster.

You have a 2-node cluster in a single-fabric SAN. Host 1 and Host 2 are part of a VMware cluster and access the same LUNs that reside in your NetApp storage. Referring to the exhibit, what would be a way to test whether the multipathing is properly configured in your environment?. Verify whether all destination storage target ports are contained in the same zone as Host 1. Administratively set ports 0a and 0c on Controller 1 to the offline setting. Disconnect Host 1 port and verify whether Host 2 is still able to run the VMs. Power off the SAN switch.

What are three supported fabric-attached MetroCluster solutions? (Choose three.). a four-node solution. a two-node solution. an eight-node solution. a two-node direct-attached solution. a two-node bridge-attached solution.

The vsadmin account for SVM vs1 is unlocked and configured with a password. Which two statements are true about login methods for the vsadmin account? (Choose two.). You access OnCommand System Manager. You access SSH. You access OnCommand Unified Manager. You access ONTAP API.

You use the commands shown in the exhibit to provision a FlexVol volume and LUN on an AFF A300. The volume shows 40% storage efficiency savings. In which container is the free space returned?. qtree. aggregate. LUN. RAID group.

You are configuring your tape backup software to authenticate to your single-node cluster by using NDMP. Referring to the exhibit, which LIF do you use to connect? (Choose the best answer.). cluster_mgmt. cluster1-01_ic1. cluster-01_mgmt1. data_lif1.

Which three tasks are SVM administrators allowed to perform? (Choose three.). Configure name services. Configure an aggregate. Monitor jobs. Configure data protocols. Create a LIF.

A storage controller named cl1-01 has disk ownership of disks in shelves 10 and 11. Its HA partner, cl1-02, has disk ownership of disks in shelves 20 and 21. Controller cl1-01 has successfully failed over to cl1-02. In this scenario, what are the owner and home attributes for disks in Shelf 11?. a home attribute of cl1 -01 and an owner attribute of cl1 -02. a home attribute of none and an owner attribute of cl1-02. a home attribute of cl1-02 and an owner attribute of cl1-01. a home attribute of cl1-02 and an owner attribute of cl1-02.

Which storage efficiency policy is automatically defined when you run volume move from a non-AFF system to an AFF system?. inline-only. promote. default. auto.

Referring to the exhibit, which LIF role is required to copy to cloud with this NetApp Data Availability Services (NDAS) solution? (Choose the best answer.). node management. cluster. data. intercluster.

Referring to the exhibit, NetApp Storage Encryption is running on node1 and node2. You move vol1 from node2 to node3. How do you ensure that the data on vol remains encrypted?. Replicate vol1 to a SnapMirror volume on node2. Enable NetApp Volume Encryption (NVE) on vol1. Install at least one shelf of self-encrypting disks on node3. Disable deduplication on vol1.

The source SVM vs1 has 50 CIFS shares, 100 NFS export policies, and four data LIFs. Referring to the SVM disaster recovery output shown in the exhibit, which two statements are true? (Choose two.). LIFs are migrated from the source to the destination. LIFs are not migrated from the source to the destination. CIFS shares and NFS export policies are not migrated from the source to the destination. CIFS shares and NFS export policies are migrated from the source to the destination.

153. When you create an SVM in ONTAP, what is the privileged account that is created to manage the SVM?. administrator. root. admin. vsadmin.

You are creating a new SVM. In this situation, which object is automatically created in the system?. SVM root volume. root aggregate. SVM management LIF. root volume.

clsuter1::> network interface modify -vserver cluster1 -lif lif1 -service-policy net-route-announce Your ONTAP 9.8 cluster administrator modified a LIF to use a new service policy. Referring to the exhibit, which type of peer connection is used by lif1?. SVM. BGP. OSPF. Cluster.

You are provisioning an SQL database VM on an AFF A400 and perform database migration operations that result in many duplicate blocks in the hosting VMFS datastore. In this scenario, which two efficiency features are helpful? (Choose two.). encryption. deduplication. inline compression. postprocess compression.

Which two performance threshold policies in OnCommand Unified manager are configurable? (Choose two.). user-defined. volume. system-defined. dynamic.

Which two resources are managed by an SVM administrator? (Choose two.). disks. aggregates. Snapshot copies. LUNs.

What are two methods to improve system administration access control security on your ONTAP environment? (Choose two.). Enable SAML Authentication using an Identity Provider that supports multi-factor authentication. Enable two-factor authentication for SSH access. Enable encrypted cluster peering for peering relationships using the cluster modify command. Enable Onboard Key Manager to encrypt volumes.

Which two protocols does ALUA support on an ONTAP cluster? (Choose two.). iSCSI. NVMe. FCP. NFS.

You are configuring an ONTAP cluster to use NVMe/FC. In this scenario, which two statements are true? (Choose two.). Create NVMe LIFs on FC target ports. Create an SVM with both NVMe and FC protocols enabled. Create an SVM with NVMe enabled. Create and start the FC service.

You want to asynchronously replicate an SVM's volumes and configuration to another NetApp cluster. Which data protection technology accomplishes this task?. SVM disaster recovery. MetroCluster. SnapVault. SnapMirror.

Which management tool would you use to add licenses to an AFF system?. NetApp Service Level Manager. OnCommand Unified Manager. OnCommand System Manager. OnCommand Insight.

Which statement is true about creating volumes that contain LUNs?. You can create LUNs on an aggregate. You cannot create qtrees on a volume that contains LUNs. You cannot create LUNs on an SVM root volume. You cannot create add files on a volume that contains LUNs.

165. An administrator has an existing host that is using FCP for access to LUNs on a NetApp SVM. The administrator replaces the host HBA and updates the zoning configuration on the FC switches. After the replacement, the host loses access to all of its LUNs. The administrator verifies that the host WWPNs successfully show up in the FLOGI database on the switches. What should the administrator do to restore LUN connectivity?. Take the LUNs offline and then bring them back online again so the host can see new paths to the LUNs. Update the initiator group mapped to the LUN with the new WWPNs. Migrate the data to newly provisioned LUNs that are mapped with the new WWPNs. The host needs to be rebooted so that it will refresh its view of the fabric.

Your customer has a Windows user that must access a volume with UNIX security style permissions. What must be done to enable the Windows user to access the volume?. The volume's security style must be changed to Mixed. The Windows user must be mapped to a valid UNIX user. A separate volume with an NTFS security style must be created. The volume's security style must be changed to NTFS.

In an aggregate with only thick-provisioned volumes, you need to split a FlexClone volume from its parent volume. There are other volumes in the aggregate. In this scenario, how much space must be available within the containing aggregate?. You need enough space for half the size of the parent volume. You need to double the space in the existing aggregate. You need enough space for twice the size of the parent volume. The split FlexClone volume must be created in a new aggregate.

You have configured SVM Disaster Recovery on your cluster, and you set the identity-preserve option to false. In this scenario, which objects are replicated?. SAN LIFs. NFS Export policies. DNS and DNS hosts. Snapshot copies.

Where would you look to find the minimum and the maximum number of array LUNS supported by FlexArray?. One Collect. Hardware Universe. Interoperability Matrix Tool (IMT). Config Advisor.

A user cannot delete the files in a volume's Snapshot copy. In this scenario, what is the problem?. The files are being used by another user. A retention period was configured for the Snapshot copy. Snapshot copies are read only. The user does not have the required permission.

The size of the aggr1 RAID group shown in the exhibit is 16. What is the RAID type?. RAID-TEC. RAID-DP. RAID4. RAID0.

You are asked to identify cache hit rates on your FAS8200 HA pair NAS volumes. You need to increase performance of your HDD cluster1_01_aggr1 aggregate. Referring to the exhibit, which NetApp technology achieves the requirement?. FlexCache. Flash Pool. FabricPool. MAX Data.

A storage administrator is not receiving performance alerts on an OnCommand Unified Manager policy that was created for a NAS volume. Which additional task is required to solve this problem?. You should assign a tiering policy. You should assign the performance threshold policy. You should clear the performance threshold policy. You should search for volume data.

A customer has zoned switches to a host, but the host cannot see the LUNs. Referring to the exhibit, what needs to be done to make the LUNs visible to the host? (Choose the best answer.). Zoning should be changed to use the 20:06:d0:39:ea:05:03:a3 and 20:08:d0:39:ea:05:03:a3 WWPNs. Ports on time-a700 nodes 1 and 2 should have the fc_nvme protocol removed. Zoning should be changed to use the 50:0a:09:81:80:d2:c3:b8 and 50:0a:09:81:42:c2:b9 WWPNs. The customer should remove the switches and directly connect the host to the controller ports.

When you use the default SnapMirror policy during transfer of a data protection SnapMirror relationship, what is transferred?. the Snapshot copy that is created by the transfer process and any existing Snapshot copies. the Snapshot copy that is manually created and any existing Snapshot copies. the SnapMirror license. only the existing Snapshot copies.

What are three default settings for SAN volumes when volumes are created with System Manager on AFF solutions? (Choose three.). Volumes are thin provisioned. Volume space is reserved from the aggregate. Aggregate inline deduplication is enabled. Volume compression is enabled. Volumes have the default snapshot schedule enabled.

You want to use SVM disaster recovery to replicate an SVM to your disaster recovery site. You have the requirements shown below. - The source and destination clusters are in different network subnets. - The source SVM is running only NAS protocols. - The CIFS server configuration should be replicated. Which two configurations are correct in this scenario? (Choose two.). The SnapMirror -identity-preserve parameter should be set to true. The SnapMirror -discard-configs network policy parameter should be used. The SnapMirror -discard-configs network policy parameter should not be used. The SnapMirror -identity-preserve parameter should be set to false.

You are configuring an ONTAP solution for FC host connectivity. In this scenario, how should the cluster be configured? (Choose two.). The SVM must be configured for Ethernet LIFs. FC ports must be configured as initiators. FCP must be licensed on the cluster. FC ports must be configured as targets.

You are using an AFF A700. In this scenario, which two default storage efficiency techniques will help save space? (Choose two.). postprocess compaction. inline deduplication. postprocess deduplication. inline compression.

Referring to the exhibit, which physical are hosting the cluster interconnect interfaces on the nodes in Cluster1?. e0a and e0e. e0a and e0b. e0b and e0c. e0c and e0a.

What are two client specifications for an export rule? (Choose two.). 0.0.0.0/0. 192.168.100.0/0. 192.168.100.0/16. 0.0.0.0/16.

According to NetApp best practice, which ports are supported for FC as shown in the exhibit?. SAS Ports. Management Ports. HA Ports. UTA2 Potts.

Which two interface group types enable the load balancing algorithm to be used? (Choose two.). load balance mode. QoS mode. dynamic multimode. static multimode.

An administrator wants to configure cluster peering between two clusters. In this situation, which role must be used when a LIF is configured?. management. data. cluster. intercluster.

Which LIF role type is used by a volume move operation between nodes?. data. cluster. intercluster. cluster-mgmt.

Which two actions create space in a nearly full FlexVol volume? (Choose two.). Enable compression. Enable deduplication. Add disks to the aggregate hosting the volume. Change the fractional reserve from 0 to 100.

You need a Flash Pool aggregate on both nodes of a 2-node cluster. You also want to maximize usable space in the SSD cache. Which Flash Pool configuration is appropriate for this situation?. Create an SSD storage pool, and then create a Flash Pool aggregate on each node. Create two storage pools and then create a Flash Pool aggregate on one node; then create another Flash Pool aggregate on the partner node to use the second storage pool. Create a Flash Pool aggregate with physical SSDs on each node. Create a Flash Pool aggregate on one node using an SSD storage pool; then create another Flash Pool aggregate using physical SSDs on the partner node.

You are asked to separate replication and data traffic into their own individual VLANs. You created two new VLANs and need to create logical interfaces (LIFs).In this scenario, what must you do before creating the LIFs? (Choose the best answer.). Create a firewall policy. Create an interface group. Create a network subnet. Create a broadcast domain.

Your company requires storage administrators to use a second authentication method when accessing OnCommand System Manager and OnCommand Unified Manager. After entering their user name and password, administrators must enter a Personal Identity Verification (PIV) code from a smart card or a mobile device. With which resource would you accomplish this objective?. a third-party identity provider. an Active Directory server. a third-party key manager. the ONTAP onboard key manager.

You are running out of space on an aggregate and decide to move a FlexVol volume to a different aggregate. You do not want to move the Snapshot copies with the volume. Which two actions satisfy your requirement? (Choose two.). Use the storage aggregate relocation command on the node. Create a FlexClone volume. Use the volume move command on the FlexCIone volume. Use the volume rehost command on the FlexClone volume.

According to NetApp best practices, when you configure FC, how many data LIFs should you create per node?. 4. 8. 6. 2.

You create SAN volumes with System Manager on a FAS solution. In this scenario, what are three default settings for these volumes? (Choose three.). A. Volumes have inline deduplication enabled. B. Volume space guarantee is set to Volume. C. Volumes have Snapshot copies disabled. D. Volume snapshot reserve is set to 0. E. Volume space guarantee is set to None.

If you change the aggr1 RAID type shown in the exhibit from RAID-DP to RAID-TEC, how many additional disks are required?. 0. 2. 1. 3.

An administrator created, a NAS storage virtual machine for a vSphere environment. The administrator verified that all interfaces can communicate successfully. However, when the administrator attempts to mount the export, a connection refuse message is received. Based on this scenario, what would you troubleshoot?. the igroup. the CIFS eport policy. the NFS export policy. the FC zoning policy.

Which two actions would you take to create a FlexGroup for the SVM vs0 in an NFSv3 environment? (Choose two.). Enable the -v3-fsid-change parameter. Use the volume flexgroup deploy command. Enable the -v3-64bit-identifiers parameter. Use the aggregate create command.

When a LUN is created in System Manager or using the CLI, which two parameters must be specified? (Choose two.). volume. qtree. aggregate. size.

You have a 4-node cluster with 2x AFF A300 and 2x FAS8200 controllers. One of the AFF A300 controllers has a 50 TB FlexVol volume that needs an immediate read-write copy for standalone testing on one of the FAS8200 controllers. Which two commands combined accomplish this task? (Choose two.). volume clone create. volume move. volume rehost. volume clone split.

Referring to the exhibit, to where will LIF4 move if you unplug the network cable from node02 port e0d?. node01 port e0c. node02 port e0c. node02 port e0d. node01 port e0d.

Which two statements are true for mailbox disks per node in an HA pair? (Choose two.). Six disks are required if the root volume is on a mirrored aggregate. Two disks are required if the root volume is on a disk shelf. Four disks are required if the root volume is on a mirrored aggregate. Eight disks are required if the root volume is on partitioned disks. One array LUN is required if the root volume is on a storage array.

If an SVM is renamed and it is participating in an intercluster SVM peer relationship, what is the result?. Remote clusters are updated with the new peer SVM name. SVM peers are removed and they need to be re-created. Snapshot copies are renamed with the new SVM unique identifier. SnapMirror relationships appear as broken and a resync is required.

An administrator has a FAS8200 system and is adding a DS224C disk shelf for Flash Pool use, consisting of 800 GB SSDs. When a flash pool is created out of these disks, what is the default RAID group type?. RAID-TEC. RAID-DP. RAID-4. RAID1.

A storage administrator wants to use Windows directory services for an SVM serving SMB shares. Users will be authenticated by domain controllers. Which two steps are required to accomplish this task? (Choose two.). Create an SVM with the NFS protocol enabled. Create an SVM with the CIFS protocol enabled. Join an SVM to a Windows workgroup. Join an SVM to a Windows Active Directory service.

An SVM CIFS server has the ability to be configured as a member of which two security models? (Choose two.). broadcast domain. workgroup. Active Directory domain. dynamic DNS (DDNS).

Which three objects are restorable from a FlexVol Snapshot copy? (Choose three.). FlexVol. NFS export. qtree. LUN. file.

Which Data ONTAP Cluster-Mode clone technology will lock a Snapshot copy?. LUN Clone. Snapshot Clone. Volume Clone. Aggr Clone.

A customer has an ONTAP 9.8 AFF A250 with 12 internal SSDs. The customer wants to expand their existing aggregates by adding 12 more SSDs to the empty drive slots in the internal shelf. Which two steps must you take to accomplish this task? (Choose two.). Manually create root-data partitions on each disk, and use both partitions to grow existing data aggregates. Add the newly created data2 partitions to the partner's existing data aggregate. ONTAP will automatically partition the SSDs when they are added to the data aggregate. Assign ownership of each SSD manually to the nodes, and they will be automatically partitioned and added.

You are configuring a NetApp cluster to communicate on VLAN 1. However, the new LIF is unable to communicate with any host in the VLAN. The network administrator has configured the switch port as an access (untagged) port on VLAN 1 and says that the VLAN is non-routed. Referring to the exhibit, what would you do to troubleshoot this problem? (Choose the best answer.). Verify that there is not IP address conflict on the network. Reconfigure the LIF to be on port e0c. Add a default gateway. Verify that the network cabling is working properly.

What are three types of load balancing for multimode groups? (Choose three.). IP. MAC Address. sequential. fixed path. most recently used.

You need to restrict SNMP access to a node management LIF to a specific subnet. In this scenario, which two commands must you verify to ensure limited access? (Choose two.). network interface show. network port vlan. network subnet. firewall policy.

You want to create an SVM disaster recovery relationship for a production SVM. When you create the destination SVM, which vserver subtype should you choose?. dp-destination. sync-destination. sync-source. default.

You have a new cluster and must create a LIF on a port that uses LACP and a VLAN. What is the correct order of network tasks that are required before you create the LIF?. VLAN -> IFGroup -> add port to broadcast domain. add port to broadcast domain -> IFGroup -> VLAN. IFGroup -> VLAN -> add port to broadcast domain. add port to broadcast domain -> VLAN -> IFGroup.

What are two benefits of using quad-path HA cabling on an AFF A700? (Choose two.). It improves resilience of the cluster. It provides double the I/O bandwidth to a stack. It improves cluster failover time. It provides double the number of shelves that you can attach.

A customer has four or more nodes in a cluster. More than four target ports are being used by the SVMs in any node. The customer wants to limit the number of paths that can be used to access LUNs on the nodes, so that the paths do not exceed the recommended maximum of eight. In this scenario, which three actions will accomplish this task? (Choose three.). Use Selective LUN Mapping. Use port sets for iSCSI. Use FC switch zoning. Use ALUA protocol. Use multipathing software.

Which two link layer discovery protocols does NetApp ONTAP support? (Choose two.). Link Layer Topology Discovery Protocol. Cisco Discovery Protocol. Link Layer Discovery Protocol. Foundry Discovery Protocol.

What is the default RAID policy for aggregates created with 10 TB disk drives? (Choose the best answer.). RAID4. RAID-DP. RAID0. RAID-TEC.

You have a 2-node NetApp cluster. You would like to use an onboard UTA2 port for host connectivity. The port was previously connected to a tape library using native FC. What must you do to configure the port for host connectivity?. Change the port mode to FC. Change the port mode to CNA. Change the FC type to initiator. Change the FC type to target.

You want to use FabricPool technology to tier SnapVault destination volumes to the capacity tier. In this scenario, which action would you perform to accomplish this task?. Create the destination volume on the FabricPool-enabled aggregate and assign the backup tiering policy to the destination volume. Create both the source and destination volumes on a standard aggregate and assign the backup tiering policy to the destination volume. Create both the source and destination volumes on the FabricPool-enabled aggregate and assign the backup tiering policy to the source volume. Create the source volume on the FabricPool-enabled aggregate and assign the backup tiering policy to the source volume.

A customer has an issue with performance on an NVMe solution. The SVM is using all four ports shown in the exhibit. In this scenario, how would the customer improve the host performance? (Choose the best answer.). Change the SFP+ in the controllers from 32 Gbps to 64 Gbps. Move all of the network interfaces to port 2a. Move some of the network interfaces from 2a to 2c and 2d. Remove support of the FC protocol and only use NVMe.

219. You are using NetApp Volume Encryption (NVE) on an AFF system. In this scenario, which two key-management solutions are supported for NVE? (Choose two.). an SSH key manager. an XTS-AES-256 key manager. the onboard key management service. a KMIP server.

220. A storage administrator has a Linux Oracle database that is using a SAN configuration with multiple dualported FC HBA connections for path resiliency and performance. The HBA ports are configured to separate FC switches. Before configuring the LUNs from the storage, what information must be obtained from the host? (Choose three.). the speed of the FC ports of the host HBAs. the amount of cache memory installed. the WWPNs of all of the FC ports installed. the status of ALUA. the status of multipathing driver.

In an HA pair, how many Intercluster LIFs are required for FabricPool?. 0. 1. 2. 4.

You want to configure Performance Manager to monitor the average latency of a volume hosting a Microsoft Exchange Server. In addition, an alert needs to be created before latency reaches 20 milliseconds. How would you accomplish this task?. Set a threshold policy for average latency with a warning of 12 and a critical warning of 15. Set a data source for average latency with a warning of 12 and a critical warning of 15. Set an event handler for average latency with a warning of 12 and a critical warning of 15. Set an event inventory for average latency with a warning of 12 and a critical warning of 15.

Your company has two separate, untrusted Active Directory (AD) domains You need to serve CIFS shares to users in both AD domains and will later merge to one AD domain. The end goal is to serve all CIFS shares out of a single SVM. In this scenario, which two actions will meet both requirements? (Choose two.). Execute the volume modify command. Create one SVM. Execute the volume rehost command. Create two SVMs.

Which two configuration limits should you verify when you add additional storage to an AFF A300 switchless configuration? (Choose two.). the supported number of SSD disks for the A300 system. the supported number of shelves. the supported number of HDDs for the A300 system. the supported number of FC initiator ports for the A300 system.

What are two causes of a storage failover partial giveback? (Choose two.). iSCSI sessions are active. SnapMirror volumes are running. CIFS sessions are active. NFSv3 mounts are active.

You want to configure a local cluster to accept SnapMirror transfers from two remote clusters. The two remote clusters have overlapping IP networks and cannot change their IP addressing scheme. In this scenario, which action would you perform to allow both remote clusters to replicate to the local cluster?. Configure network address translation (NAT) on the network. Configure two ONTAP subnets with distinct IP address allocations. Configure the SnapMirror relationships as type XDP. Create separate IPspaces on the local cluster.

What is the default fractional reserve for a thin-provisioned SAN volume?. 5%. 20%. 100%. 0%.

You created a dedicated SVM for CIFS on a FAS8200 2-node cluster using multiple disk types. In this scenario, which action ensures that this SVM hosts volumes only on SATA drives?. Edit the SVM resource allocation. Assign all the SATA drives to a CIFS SVM. Move the SAS and SSD aggregates to a different node. Create a FlashPool aggregate with SATA drives.

In which version of ONTAP did the NVMe protocol become available for SAN environments?. 9.4. 9.5. 9.3. 9.2.

Where would a cluster administrator move a FlexVol volume using the volume move command?. only to an aggregate on the partner node. to aggregates on other nodes in the cluster. to any node that does not host a SnapMirror of the same FlexVol. to another SVM in the cluster.

A storage administrator has a single-node FAS cluster. The administrator wants to add a second node to convert the FAS storage array into a switchless cluster. In this scenario, what would the administrator do to accomplish the task?. Add a new AFF HA pair and replace the existing FA. Add a cluster interconnect switch and a second FAS of the same model. Add a new single node AFF controller to the existing FAS storage array. Add a new single node FAS controller of the same model.

You want to configure Active Directory authentication for a cluster. You have performed the following actions: - created the SVM, - joined the SVM to Active Directory, - created the domain tunnel. You attempt to log in to the cluster as an Active Directory user but access is denied. How would you solve this problem?. Create a cluster user account with the same username and password as the Active Directory user. Create a cluster user account within Active Directory. Create a custom role that allow Active Directory tunneling. Create an Active Directory user account on the cluster.

NetApp supplied a replacement for a failed drive, but the replacement drive does not show up as a spare. Referring to the exhibit, which statement is true?. You exceeded the maximum drive count for the controller platform. The failed disk was not sanitized before removal. The automatic assignment policy is set to the default. Automatic disk assignment is disabled.

You have a 4-node cluster and want to ensure that a new NAS LIF can fail over to any node. In this scenario, which two actions are required to configure the LIF? (Choose two.). Add ports from all nodes to the LIF's broadcast domain. Configure the failover policy to broadcast-domain-wide. Add ports from all nodes to the LIFs home port list. Configure the failover policy to system-defined.

You want e-mail notifications sent to you automatically when latency reaches a warning level of 15 milliseconds and a critical level of 20 milliseconds on a volume that stores your Oracle database files. In this scenario, which type of threshold policy should be created within OnCommand Unified Manager?. a LUN Threshold Policy. a Cluster Threshold Policy. a Volume Threshold Policy. an SVM Threshold Policy.

You are asked to create a new SVM to serve SMB data using Active Directory authentication. Which two requirements must be satisfied prior to serving data? (Choose two.). DNS must be enabled and configured correctly. The CIFS license must be installed on the storage system. An intercluster LIF must be created for serving SMB data. An administrative user must be created for the SMB SVM.

You are configuring replication between two NetApp clusters. You want to configure disaster recovery and vaulting on the same destination volume. In this scenario, which SnapMirror relationship type and SnapMirror policy type should be used?. a relationship type DP and a policy type vault. a relationship type DP and a policy type mirror-vault. a relationship type XDP and a policy type vault. a relationship type XDP and a policy type mirror-vault.

What is the compression group size for adaptive compression?. The group size is always 32k, regardless of the workload. The group size is always 4k, regardless of the workload. The group size is always 8k, regardless of the workload. The group size is determined based upon the workload.

You use the Automated Workload Analyzer (AWA) to identify workloads that would benefit from which feature?. Flash Pool aggregates. FabricPooI capacity tier. storage efficiency. Advanced Disk Partitioning.

You must enable remote authentication and grant a remote administrator either cluster admin or vsadmin access. In this scenario, which three authentication types are supported for ONTAP 9.7? (Choose three.). AD. SAML. CHAP. LDAP. RADIUS.

With which type of I/O is data compaction beneficial?. I/O and files 4 KB or larger. I/O and files less than 2 KB. I/O and files 8 KB or larger. I/O and files 16 KB or larger.

Which NetApp product enables you to leverage legacy storage investments?. FlexClone. FlexGroup. Cloud Volumes ONTAP. FlexArray.

Which three privileges are available to the vsadmin role? (Choose three.). setting physical port speeds. managing LUNs. managing volumes, except volume moves. managing aggregates, except aggregate relocate. configuring protocols.

You are troubleshooting a Linux host named host1 that sees a connection refused message when you execute the ssh admin@192.168.1.240 command. Referring to the exhibit, what is the reason for this message?. There is no route to the host. The firewall policy is blocking the host. NTP is set up incorrectly. DNS is not resolving the host name.

What are three reasons to implement FabricPool? (Choose three.). to shrink secondary storage. to implement storage efficiency features. to move volumes to external capacity tiers. to use the volume backup feature. to reclaim space on primary storage.

An administrator encountered a ransomware attack that affected the active file system data. They have been creating Snapshot copies on an hourly schedule. They determine that the entire volume needs to be recovered. volume snapshot delete. volume snapshot create. volume snapshot restore. volume snapshot modify.

You want to use external tools to monitor your ONTAP cluster’s performance metrics so that your operations team does not have to log in to the cluster. Which three tools allow you to accomplish this task? (Choose three.). OnCommand Insight. OnCommand Workflow Automation. Active IQ Unified Manager. ONTAP System Manager. Cloud Insights.

You want to create a FlexGroup volume that contains four aggregates with eight constituents each. In this scenario, what is the value of the aggregate list multiplier?. 8. 4. 32. 2.

Which command enables the vsadmin account?. security login domain-tunnel create. security login modify. security login unlock. security login create.

You are asked to deploy a two-node ONTAP Select system. The physical hardware is located in two different locations. You must ensure high availability and automated switchover. Which two steps would you take to satisfy this requirement? (Choose two.). Ensure that the ONTAP Select Deploy VM resides at a third location other than the two datacenters. Use ONTAP Select Deploy to install the nodes on the physical hardware. Ensure that the SyncMirror license is installed on the cluster. Use Active IQ Unified Manager to provide a quorum for the two nodes.

As an administrator, you are asked to enable deduplication on volumes that are separated by workloads on a FAS8200 system.On which volume would you see the highest savings from enabling deduplication?. home directory shares. virtual desktop environment. file share. SQL database.

Which management tool would you use to deploy a new instance of Cloud Volumes ONTAP?. OnCommand System Manager. OnCommand Unified Manager. Cloud Volumes Service. OnCommand Cloud Manager.

An administrator created, a NAS storage virtual machine for a vSphere environment. The administrator verified that all interfaces can communicate successfully. However, when the administrator attempts to mount the export, a connection refuse message is received. Based on this scenario, what would you troubleshoot?. the igroup. the CIFS eport policy. the NFS export policy. the FC zoning policy.

A customer requires that their data is fully protected from theft, both at the volume layer and at the disk layer. Which two features of ONTAP satisfy this requirement? (Choose two.). Kerberos. NetApp Volume Encryption. Challenge Handshake Authentication Protocol. NetApp Storage Encryption.

Referring to the exhibit, what is the throughput limit for the shares0 volume?. 250 IOPS. 25 MB/s. 50 MB/s. 1000 IOPS.

An administrator realizes that daily snapshots are not being replicated to their destination. The administrator can see the daily snapshots created at the source. The exhibit shows the policy in use. Weekly snapshots are being replicated without a problem, and the SnapMirror relationship is showing as "healthy". In this scenario, what is causing the problem with the daily snapshot?. The vault policy applied to the source volume does not match the SnapMirror policy at the destination. The SnapMirror label has not been applied to the daily snapshots. The SVM peer is not working. The daily snapshots at the source are busy due to the NDMP backup.

A 2-node switches cluster experiences a node failure. In this situation, which LIF automatically migrates to a different port?. SAN data LIF. intercluster LIF. NAS data LIF. node management LIF.

An administrator forgot to update the cabling sheet for a core Cisco switch and cannot recall which ports were used by the NetApp FAS system. Which command should the administrator run to obtain this information?. network port show. network device-discovery show. network interface show. network port broadcast-domain show.

Which command shows the data compaction savings for an aggregate?. storage efficiency show. storage aggregate show—space. storage aggregate show—efficiency. volume efficiency show.

261. Which statement about a node-root volume is true?. A node-root volume is used as the root volume for all of the SVMs for that node. The volume move command can be used to move a node-root volume. There is only one primary root volume per node in the cluster. A node-root volume may be used for customer data.

A newly created FC LUN is not visible to a Windows 2016 server containing other LUNs in the cluster that are working properly.In this scenario, what must be verified in the solution?. The FC protocol is licensed on the cluster. An igroup mapping exists to the LUN. NPIV is enabled on the switch. The WWPN is in the Brocade/Cisco zone configuration.

263. Two 100 GB space-reserved LUNs and one 100 GB non-space-reserved LUN were created in System Manager in a 1 TB volume.In this scenario, how much space has been allocated for writes to the three LUNs?. 300 GB. 1 TB. 200 GB. 100 GB.

You are asked to delete an SVM that was used for CIFS. Which two steps must be completed prior to completing this task? (Choose two.). Delete all LIFs from all SVMs. Stop the SVM. Delete all data volumes in the SVM. Delete the CIFS license.

Which NetApp tool is used to perform a configuration validation and health check that includes a highavailability setup?. Inventory Collect Tool. Hardware Universe. SnapCenter. Config Advisor.

You use DNS zone delegation to access an SVM that is set up for on-box DNS to nfs1.netapp.com. You can ping both lif1 and lif2 by IP address, but you can only ping lif1 by the delegated DNS name nfs1.netapp.com. Referring to the exhibit, what must you do to allow on-box DNS access to lif2?. Configure lif2 in the external DNS. Configure the name service to allow DNS. Modify the DNS zone on lif2 to nfs1.netapp.com. Modify the firewall policy on lif2 to management.

What are three firewall policies? (Choose three.). cluster. node. data. mgmt. intercluster.

SVM root volume protection should be configured when which two protocols are in use? (Choose two.). NFS. CIFS. FCP. iSCSI.

The exhibit shows a Windows 2019 server with two FC HBAs using ALUA. How many paths to LUN1 are active/optimized? (Choose the best answer.). 8. 2. 4. 1.

Which FabricPool policy would you apply only on a SnapMirror destination volume?. backup. destination. auto. manual.

You want to replace the key management passphrase on a FAS8200 system using onboard NetApp Storage Encryption (NSE). Which action accomplishes this task?. Perform a takeover-giveback of each node in the cluster to update the passphrase on each mode. Use the security key-manager setup command to change the passphrase. Use the volume move command to migrate a volume and update the passphrase during the move. Use the security key-manager update-passphrase command to change the passphrase.

You need to create a new LIF on VLAN 10. The port-channel configuration on the upstream switch has VLAN 10 set to the native (untagged) VLAN. In this scenario, what should be set as the LIF's home port?. e0c. a0a. e0c-10. a0a-10.

What is the minimum number of disks required to create a RAID-DP data aggregate?. 6. 3. 4. 5.

You are planning to present storage to your servers from your AFF system using FC protocol. You have a pair of FC switches to ensure connectivity and you have decided to use WWPN zoning. Referring to the exhibit, which two WWPNs do you use for your configuration? (Choose two.). fc-2 WWPN. fc-1 WWPN. 0d WWPN. 0c WWPN.

An administrator created an SVM for a VMware vSphere 6.5 cluster. For the SVM, the NFS protocol was enabled. Data LIFs were configured with jumbo frames. The nfs01 volume was created and mounted as junction path / nfs01. A VMware export policy that allowed all the hosts of the cluster was applied to the SVM. However, the hosts are unable to mount the volume. In this scenario, what caused the problem?. NFS v3 is not compatible with ESXi hosts. The volume is not thin provisioned. The maximum transmission unit (MTU) was not set properly on the ESXi hosts. The default export policy needs to allow reads from the ESXi hosts.

On an All Flash FAS, where is the root parity information located on a node using Advanced Disk Partitioning?. distributed among SSD partitions. on a single SSD partition. on two SSD drives, regardless of RAID type. on a single SSD drive, regardless of RAID type.

What are two security types available for NFSv3 shares? (Choose two.). AUTH_SYS. unified. Kerberos vs. mixed.

You have a volume storing a large number of 1KB to 2KB compressed zip files. In this scenario, which storage efficiency feature should you use?. data compaction. secondary compression. adaptive compression. deduplication.

You want to enable jumbo frames for iSCSI traffic on your cluster. To satisfy this requirement, what would you modify on the cluster?. iSCSI LIFs. broadcast domains. network ports. igroups.

What are three tiering policies that are associated with a FabricPool-enables aggregate? (Choose three.). backup. mirror-vault. local-only. auto. snapshot-only.

What are three advantages of configuring network subnets? (Choose three.). The DNS zone is automatically set on the NAS LIF. The IP address is automatically set on the NAS LIF. The flow control is automatically set on the port. The default gateway is automatically added to the SVM. The subnet mask is automatically set on the NAS LIF.

You are creating a CIFS-based SVM, but the SVM cannot join the domain. In this scenario, which two actions would be helpful in troubleshooting the problem? (Choose two.). Verify that each node has a data LIF. Verify that the cluster admin account is used to join the Active Directory. Verify that the clocks are synchronized between the SVM and the domain controller. Verify that the data LIF can access the Active Directory domain controller.

There is a node in your cluster that needs to be halted to replace a hardware component. Which two statements are true in this scenario? (Choose two.). FlashCache data hosted on the failed node will migrate to its partner. A FlashPool-enabled volume hosted on the failed node will be taken over by its partner. An aggregate hosted on the halted node will be taken over by its partner. A SAN LIF hosted on the halted node will migrate to a healthy node.

A storage administrator is troubleshooting CIFS share connection issues. In this scenario, what would be three causes for these issues? (Choose three.). The cluster time is not synchronized with the domain controller. The NIS service is not running. The machine account has been deleted in the Active Directory. The machine password is not synchronized with the domain controller. The number of allowable CIFS shares have been exceeded.

The NVM Express (NVMe) flash capacity is upgradeable in which two systems? (Choose two). FAS9000. FAS8200. FAS2650. AFF A700.

287. Which of the following statements is true about a Flash Pool?. A 32 bit or 64 bit aggregate containing SSDs and HDDs. A 32 bit aggregate containing SSDs and HDDs. A 64 bit aggregate containing SSDs and HDDs. A 64 bit aggregate containing only SSDs.

You configure a new LUN on a NetApp cluster, and you can successfully access it from the host. An application using the new LUN is having storage performance problems, and ONTAP is reporting misalignment on the LUN. In this scenario, what is causing the performance and misalignment problems?. The LUN was created with the incorrect OS type. The host does not support ALUA. The igroup is configured without Selective LUN Mapping (SLM). The host is using a non-optimized SAN path.

You are asked to investigate possible solutions for increasing the performance of a read-intensive, NFSv3 workload in your FAS environment. Which two NetApp technologies would satisfy the requirement? (Choose two.). Flash Pool. FabricPool. FlexCache. FlexVol.

You must create separate SVMs that are based on teams. You also need to create separate SVMs that are based on the block-level and file-level protocols. Your DevOps team requests NFS and CIFS protocols, your AI team requests NFS and NVMe protocols, and your marketing team requests SMB and iSCSI protocols. In this scenario, what is the minimum number of SVMs that you must create to satisfy these requirements?. 3. 5. 6. 4.

You are attempting to establish a SnapMlrror relationship between your ONTAP cluster (AcmeClusOl) and a partner company's ONTAP cluster (WidgetsClusOl). The clusters are unable to establish a peering relationship. You perform a packet capture on WldgetsClusOl and do not see any packets from AcmeClusOl. You also discover that the IP subnet that Is used for WidgetsClusOl's intercluster LIFs overlaps with a local subnet at your company. In this scenario, which feature would enable AcmeClusOl and WidgetsClusOl to peer with each other?. VLANs. broadcast domains. IPspaces. ONTAP subnets.

292. Which two storage efficiency features are enabled by default on AFF systems? (Choose two.). LUN-level compression. aggregate-level compression. aggregate-level inline deduplication. volume-level Inline deduplication.

All SMB users are reporting that their network share performance Is slow on a new NetApp FAS500f HA pair. You determine that the users have converged network adapters (CNAs) with flow control enabled and no option to disable. In this scenario, which two flow control settings are recommended on the NetApp ONTAP physical ports? (Choose two.). Disable flow control end-to-end on data network ports. Enable flow control end-to-end on cluster network ports. Enable flow control end-to-end on data network ports. Disable flowcontrol end-to-end on cluster network ports.

Your company wants to Increase access security In both their NFS and ISCSI environments. Currently ISCSI Is not authenticated and NFS relies only on export policies for security. Which two enhancements do you use to satisfy this new criteria? (Choose two.). Enable Kerberos for NFS exports. Enable Kerberos for iSCSI LUN access. Enable Challenge-Handshake Authentication Protocol (CHAP) for NFS exports. Enable Challenge-Handshake Authentication Protocol (CHAP) for ISCSI LUN access.

You are caching on-premises ONTAP volumes into the cloud with Cloud Volumes ONTAP as shown in the exhibit. In this scenario, which two protocols are supported? (Choose two.). SMB. NVMe. ISCSI. NFS.

After attempting to perform an ONTAP upgrade. It falls during the pre-check. In this scenario, what would cause this problem?. encrypted volumes. offline volume. Idle SnapMirrors. offline data LIF.

What establishes a quorum in a 4-node cluster?. epsilon. cluster peer. ONTAP Mediator. TieBreaker.

You have an SVM-DR relationship as shown in the exhibit. You are given a new requirement to use SnapMirror Synchronous (SMS) for the data volumes In NFS-SVM-01. In this scenario, which solution Is supported to enable SMS in ONTAP 9.8 software?. Set up new SM-S relationships from the AFF A220 to a new destination. Set up new SM-S relationships from the FAS2720 to a new destination. Set up NetApp Cloud Sync with a cloud broker in AWS to replicate to a new destination. Modify the existing SVM-DR policy to use sync mode.

An application owner at your organization requests a solution for zero RTO In the event of a failure In your primary data center, where you are using NetApp ONTAP 9.8 software with ISCSI LUNs. The owner wants to avoid reconfiguring the application. Which NetApp solution would you propose to fulfill these requirements?. SyncMlrror. SnapMirror Business Continuity (SM-BC). SVM Disaster Recovery (SVM DR). SnapMirror Synchronous (SMS).

You are the administrator of an ONTAP 9.8 cluster. Your company wants to know how many files are In the NAS volumes of the cluster and how old these files are. Which two tools fulfill this requirement? (Choose two.). Active IQ Config Advisor. Active IQ Unified Manager. ONTAP System Manager. ONTAP CLI.

Your company wants their newly Installed ONTAP system to automatically send telemetry data to NetApp to provide early notification of any security risks, bug fixes, and ONTAP updates. Furthermore, In case of hardware failures, a support case should be opened automatically at NetApp. Which two NetApp components satisfy the requirements? (Choose two.). Cloud Insights. Active IQ. ONTAP AutoSupport. Active IQ Unified Manager.

After an ONTAP upgrade, you notice that several cluster LIFs are not on their home ports as shown in the exhibit. Which LIF option would change this outcome?. the subnet-name option. the failover-policy option. the auto-revert option. the data-protocol option.

Which security method would be used to authenticate targets and Initiators In an ISCSI environment?. NIS. LDAP. /etc/hosts. CHAP.

Referring to the exhibit, what would cause a customer to have an Issue with SVM eplc_fcp when mapping a namespace to a host?. FC has not been licensed on the cluster. NVMe Is not configured for the SVM. FC switch zoning has not been done correctly. NVMe is not licensed on the cluster.

You recently added a new ESXi host to your VMware vSphere cluster. However, you cannot mount any of the existing NFS datastores to the host. Referring to the exhibit, which action solves the problem?. Add NFSv4 to the access protocols. Enable Kerberos in the export policy. Add SMB/CIFS to the access protocols. Add HOST 3's IP address to the NFS export policy.

You need to Increase the number of files that can be created In a volume. Which two methods enable you to achieve this goal? (Choose two.). Increase the number of files permitted on the volume. Set the space guarantee to 'volume". Set the fractional reserve to "0". Increase the size of the volume.

You have received an alert from Active IQ Unified Manager that interface eOc has gone offline. Network engineering asks for the corresponding MAC address for the port that has a problem. Referring to the exhibit, which MAC address would you supply to the engineering team?. 02:a0:98:fl:2e:be. 00:a0:98:fl:2e:b2. 00:a0:98:fl:2e:b3. 02:a0:98:fl:21:88.

SnapMirror Business Continuity (SM-BC) relies on a component to trigger an automatic unplanned failover (AUFO). In this scenario, what is this component?. ONTAP Deploy. Tiebreaker software. ONTAP Mediator. Cloud Manager.

You have created a new FlexCache cache volume and want to warm the cache before clients access the cache volume for the first time. In this scenario, how would you accomplish this task?. Prepopulate the cache volume with data from the origin volume using the flexcache prepopulate start command. Enable block-level Invalidation using the volume flexcache origin config modify command. Copy the data from the origin volume to the cache volume with the NetApp XCP Migration Tool. Synchronize the origin and cache first with the volume flexcache sync-properties command.

You have a NetApp AFF A400 HA pair with Fabric Pool enabled on all data using the snapshot-only policy. Users are reporting slow restores when they recover files with the Windows Previous Versions tab. Referring to the exhibit, what is the highest latency seen on restore?. 10500. 10021. 9591. 7889.

When you perform an upgrade using ONTAP System Manager 9.8, which two statements are true? (Choose two.). The latest available Images will appear In the ONTAP System Manager interface. The images will be automatically uploaded to the cluster by using the ONTAP System Manager interface from the NetApp Support site. The update history is available within the ONTAP System Manager interface. The Images must be manually uploaded to the cluster by using the ONTAP System Manager interface.

A user cannot save a file on an ONTAP SMB share. Referring to the exhibit, which action allows the user to save the file?. Allow the file type *, rtf In the CIFS Server fpolicy. Let the user save the file to a writeable location. Synchronize the ONTAP Cluster time to the Active Directory time. Set the user permission for the share to write.

You want to scale out storage performance for read-Intensive data across multiple locations. In this scenario, which NetApp feature accomplishes this task?. FlexClone. FlexVol. FlexCache. Flash Pool.

You create a storage virtual machine (SVM) called SVM500 that is provisioned for iSCSI. After creating a LUN in the SVM and mapping it to an igroup, the attached VMware hosts are unable to mount the LUN. Referring to the exhibit, what is the issue?. The igroup contains the wrong protocol. The igroup contains multiple Initiators. The initiator is a member of igroups of different OS types. The igroup does not contain the appropriate initiators.

You are currently using SnapMlrror Synchronous (SM-S) to protect a critical workload at your organization and you want to convert the SnapMlrror policy from Sync to StrictSync. In this scenario, which procedure allows you to achieve this task?. Recreate the SnapMirror relationship, specifying the strictsync policy, then re-synchronize it. Modify the existing SnapMirror relationship specifying the strictsync policy, then re-synchronize It. Recreate the SnapMlrror relationship, specifying the strictsync policy, then promote It. Modify the existing SnapMirror relationship specifying the strictsync policy, then promote It.

Which configuration Is supported using NetApp's All SAN Array (ASA)?. 24-node cluster. single node cluster. 2-node cluster. 12-node cluster.

After deploying an ONTAP 9.8 cluster, you want to disable the unused Ethernet ports. In this scenario, which two methods would accomplish this task? (Choose two.). Use ONTAP System Manager. Use the command line interface. Use Active IQ Config Advisor. Use Active IQ Unified Manager.

Your company requests that the monthly performance data of your ONTAP 9.8 cluster be exported to a CSV file for further processing. In this scenario, which three NetApp products satisfy this requirement? (Choose three.). Active IQ Unified Manager. Cloud Insights. Active IQ Config Advisor. ONTAP System Manager. Active IQ OneCollect.

You want to enable the Internal ONTAP engine that quickly Identifies the file and directory differences between two Snapshot copies. In this scenario, which feature would accomplish this task?. SnapVault. SnapCenter. SnapDIff. SnapLock.

You are asked to deploy a 2-node ONTAP Select cluster. The physical hardware Is located In two different locations and you want the aggregates mirrored synchronously between the two data centers. You must ensure high availability and automated switchover. In this scenario, which two steps would you take to fulfill this requirement? (Choose two.). Ensure that the ONTAP Select Deploy VM resides at a third location other than the two data centers. Install the SnapMirror Sync license on the cluster. Use ONTAP Mediator serviceto make sure that you have a quorum for the two nodes. Use ONTAP Select Deploy to Install the nodes on the physical hardware.

You attempt to create an SVM for CIFS access only. In this scenario, which three actions must be performed to Join the existing Active Directory? (Choose three.). Create DNS entries. Create a data LIF. Create export policies. Create NTP entries. Create a cluster LIF.

You want to prepare your ONTAP cluster and your ESXI cluster to connect NFS datastores over a 10-GbE network using Jumbo frames. In this scenario, which three configurations would accomplish this task? (Choose three.). Enable jumbo frames with an MTU of 9000 for your ESXi hosts. Enable jumbo frames with an MTU of 9216 for your switches. Enable Jumbo frames with an MTU of 1500 for your ESXI hosts. Enable Jumbo frames with an MTU of 1500 for your ONTAP cluster. Enable Jumbo frames with an MTU of 9000 for your ONTAP cluster.

After creating several volumes, you notice that the hosting aggregates Immediately show a decrease In available space. Which volume setting would prevent this outcome?. space SLO set to "thick". space guarantee set to "none". space SLO set to "semi-thick". space guarantee set to "volume".

Exhibit. Miss----------------- The availability of the remote cluster in the peering relationship shows "Partial." Referring to the exhibit, what is the reason for this status message?. The remote cluster does not have its cluster license applied properly. The local cluster is unable to authenticate successfully to the remote cluster. Some nodes In the local cluster are not able to contact some or all nodes in the remote cluster. The Intercluster LIFs on the local cluster are unavailable and not able to communicate to the remote cluster.

When you set up an ONTAP cluster, which two SVM types are automatically created? (Choose two.). admin. node. data. cluster.

Which statement Is correct about Temperature Sensitive Storage Efficiency (TSSE)?. TSSE Is enabled automatically on newly created thick provisioned volumes. TSSE operations on a AFF array are automatically throttled depending on whether data Is hot or cold. TSSE operations on Cloud Volumes ONTAP are automatically throttled depending on whether data is hot or cold. TSSE operations on ONTAP Select are automatically throttled depending on whether data is hot or cold.

Exhibit. Miss----------------- You have an ONTAP 9.8 cluster. After network maintenance, the LIF that is shown in the exhibit is not always on a correct port and is unreachable by users until the LIFs are moved to port eOc or eOd on either storage node. In this scenario, which action should you take to ensure that the LIF only fails over to the correct ports?. Create a DNS load balancing zone. Split the broadcast domain. Create an IPspace. Change the LIFs failover policy to sfo-partner-only.

You have commissioned a new AFF A250 MetroCluster over IP configuration. Your company requires an automatic switchover to the surviving site In case of a site disaster. What do you need to configure to fulfill this requirement?. cluster failover. ONTAP Mediator service. storage failover. automated unplanned switchover.

Which two statements are true about NVMe? (Choose two.). NQNs are added to namespaces. LUNs are mapped to Initiator groups. NQNs are added to subsystems. Namespaces are mapped to subsystems.

You are adding a NetApp AFF A400 system to an existing 4-node cluster and want to know which ports you would use to expand your cluster. Referring to the exhibit, which tool would you use to accomplish this task?. Active IQ Unified Manager. NetApp Interoperability Matrix (IMT). Active IQ Conflg Advisor. NetApp Hardware Universe (HWU).

You have a remote FlexCache storage device that is running on ONTAP Select 9.8 software. The cache origin volume Is on an FAS8700 that is running ONTAP 9.8 software. The WAN connection dropped, and the FlexCache volume is in disconnected mode. In this scenario, which LIFs would you ping to troubleshoot the disconnect?. management. Intercluster. data. cluster.

You need to configure data-at-rest encryption for your NetApp ONTAP 9.8 cluster. Your company does not have Key Management Interoperability Protocol (KMIP) services available but must require a passphrase to be entered when a node Is rebooted. In this scenario, which two actions should be performed to satisfy these requirements? (Choose two.). Configure an external key management server. Enable onboard key management. Enable cluster-wide FlPS-compliant mode. Enable common criteria mode.

A customer wants to migrate a series of LUNs from a third-party array to a FAS. In this scenario, which two tools would the customer use? (Choose two.). ADP. XCP. FLI. NKS.

You have a 2-node NetApp FAS2750 ONTAP cluster. You create a new 20-GB LUN In a new 100-GB volume and write 10 GB of data to the LUN. No storage efficiencies are enabled for the volume or aggregate. Referring to the exhibit, which two statements are true? (Choose two.). ONTAP reports that the volume Is using 10 GB of Its containing aggregate. ONTAP reports the volume as 20% full. ONTAP reports that the volume Is using 100 GB of its containing aggregate. ONTAP reports the volume as 10% full.

You have an ESXI cluster with VMware VMFS LUNs on an AFF A400 system. After troubleshooting performance Issues, you determine that timeout best practices are not set on the hosts. In this scenario, which NetApp tool would apply the best practice settings?. SnapCenter Plug-in for VMware vSphere. SAN Host Utilities. Virtual Storage Console (VSC). SnapManager.

A Linux host with the 10.0.1.24 IP address is unable to mount the VOL_A volume using NFSv3. Referring to the exhibit, what is the problem?. The host IP address does not match the export policy rule. The volume is in read-only. The volume is not mounted In the namespace. The logical Interface does not allow the NFSv3 protocol.

Your company has purchased two NetApp AFF A400 HA pairs. During deployment, how many root aggregates are created?. 6. 4. 2. 8.

Your company runs a NetApp AFF A220 cluster as a file server for NFS and SMB. You want to use one of the unused ports to connect a single Windows host directly, using FC. You have converted the UTA2 ports e0e and e0f to FC and equipped them with a 16-Gbps FC transceiver. Your Windows host fails to connect to the storage. In this scenario, which action solves the problem?. Use an FC switch between storage and host. Use the arbitrated loop topology on storage and host. Use the point-to-point topology on all ports. Use an Ethernet switch between storage and host.

Windows 2019 reports 500 GB of free space on a disk; however, on the storage side, the LUN has 0 bytes free. When the host deletes files on the disk, auto reclaim on the thin-provisioned LUN does not occur. In this scenario, which action should you take to enable space reclamation?. Set the space allocation option to disable. Set the space allocation option to enable. Enable space guarantees on the volume. Enable space guarantees on the LUN.

You want to configure Active Directory domain controller access for NetApp ONTAP cluster administration. In this scenario, which two actions would accomplish this task? (Choose two.). Configure an authentication tunnel through an admin SVM. Use the vservar active-directory create command to create a computer account on the domain for a non-CIFS SVM. Use the vserver active-directory create command to create a computer account on the domain for a CIFS SVM. Configure an authentication tunnel through an existing CIFS SVM.

A volume Is set to use Adaptive QoS with the default policy. In this scenario, which change would affect the QoS throughput ceiling?. Data is added to the volume. Disks are added to the volume's aggregate. More clients access the volume. The volume is resized.

You are asked by your network engineering team to make sure that your NetApp cluster Is configured to run LACP on Its network ports. Which network component satisfies this request?. VLAN. Interface group. broadcast domain. failover group.

You are the administrator of an ONTAP 9.8 cluster. You have configured an hourly snapshot schedule for all NAS volumes. One of your users accidentally deleted an Important spreadsheet file on an SMB share. The file needs to be restored as quickly as possible by the Windows user. Which statement is correct in this scenario?. On the cluster CLI, execute the volume clone create command with the -parent-snapshot option set to the latest Snapshot copy and share the cloned volume as an SMB share, then copy the file back. On the cluster CLI, execute the volume snapshot restore-file command with the options to select the Snapshot, path, and restore-path. In ONTAP System Manager, navigate to the volume where the share resides, click on snapshot copies and restore the latest Snapshot copy. In Windows Explorer, right-click on the SMB share where the file was deleted, go to previous versions select the file and copy It to the original location.

You want to add SSDs to existing HDD aggregates. Which NetApp tool helps you to validate how many SSDs would Improve performance?. OnCommand Workflow Automation. Active IQ Unified Manager. ONTAP System Manager. Automated Workload Analyzer.

After creating an SVM In an ONTAP cluster, you are asked to delegate administration of the newlycreated SVM to an SVM administrator. Create the vsadmin user account in the new SVM. Create a LIF for SVM management. Configure role-based access control (RBAC) for the vsadmin user account. Set a password for (the vsadmin user account.

Your company requires WORM archiving of data on their ONTAP cluster. The data must not be able to be deleted even by an administrator. Which ONTAP feature fulfills this requirement?. SnapLock Compliance. SnapMlrror software. SnapLock Enterprise. SnapVault software.

347. Which three protocols are supported by NetApp ONTAP Select? (Choose three.). NFS. SCSI. NVMe. FCP. CIFS.

You have an Internet of Things (IoT) application that will use SMB shares on a remote ONTAP Select Instance. There are no name services and only a local network Is available at the remote IoT site. In this scenario, which two features are supported by ONTAP software for the IoT application? (Choose two.). Active Directory users. SMB Server in workgroup mode. SMB3 Witness protocol. CIFS local users.

A user wants existing data in a FlexVol created in ONTAP 9.1 to be placed into a FlexGroup volume with ONTAP 9.8. In this scenario, which two statements are true? (Choose two.). Use XCP to copy data from a FlexVol to a FlexGroup. Use SnapMirror to replicate data from FlexVol to FlexGroup. You can convert the FlexVol volume to a FlexGroup volume. A FlexVol to FlexGroup conversion is not supported.

Which two types of capacity tiers are supported with FabrlcPool aggregates In ONTAP 9.8? (Choose two.). SWIFT Object Store. NFS Export. StorageGRID Object Storage. S3 Object Store.