Prefiromacarrao

Refer to the exhibit. The exhibit displays the output of the CLI command: diagnose sys ha dump-by vcluster. Which two statements are true? (Choose two.). A. FortiGate SN FGVM010000065036 HA uptime has been reset. B. FortiGate devices are not in sync because one device is down. C. FortiGate SN FGVM010000064692 is the primary because of higher HA uptime. D. FortiGate SN FGVM010000064692 has the higher HA priority.

On FortiGate, which type of logs record information about traffic directly to and from the FortiGate management IP addresses?. A. System event logs. B. Forward traffic logs. C. Local traffic logs. D. Security logs.

Refer to the exhibit. An administrator has configured a performance SLA on FortiGate, which failed to generate any traffic. Why is FortiGate not sending probes to 4.2.2.2 and 4.2.2.1 servers? (Choose two.). A. The Detection Mode setting is not set to Passive. B. Administrator didn't configure a gateway for the SD-WAN members, or configured gateway is not valid. C. The configured participants are not SD-WAN members. D. The Enable probe packets setting is not enabled.

Which two configuration settings are synchronized when FortiGate devices are in an active-active HA cluster? (Choose two.). A. FortiGuard web filter cache. B. FortiGate hostname. C. NTP. D. DNS.

Which two statements are correct about SLA targets? (Choose two.). A. You can configure only two SLA targets per one Performance SLA. B. SLA targets are optional. C. SLA targets are required for SD-WAN rules with a Best Quality strategy. D. SLA targets are used only when referenced by an SD-WAN rule.

Which two statements are correct about NGFW Policy-based mode? (Choose two.). A. NGFW policy-based mode does not require the use of central source NAT policy. B. NGFW policy-based mode can only be applied globally and not on individual VDOMs. C. NGFW policy-based mode supports creating applications and web filtering categories directly in a firewall policy. D. NGFW policy-based mode policies support only flow inspection.

Which engine handles application control traffic on the next-generation firewall (NGFW) FortiGate?. A. Antivirus engine. B. Intrusion prevention system engine. C. Flow engine. D. Detection engine.

By default, FortiGate is configured to use HTTPS when performing live web filtering with FortiGuard servers. Which CLI command will cause FortiGate to use an unreliable protocol to communicate with FortiGuard servers for live web filtering?. A. set fortiguard-anycast disable. B. set webfilter-force-off disable. C. set webfilter-cache disable. D. set protocol tcp.

Refer to the exhibits. Exhibit A shows system performance output. Exhibit B shows a FortiGate configured with the default configuration of high memory usage thresholds. Based on the system performance output, which two statements are correct? (Choose two.). A. Administrators can access FortiGate only through the console port. B. FortiGate has entered conserve mode. C. FortiGate will start sending all files to FortiSandbox for inspection. D. Administrators cannot change the configuration.

Which statement about the policy ID number of a firewall policy is true?. A. It is required to modify a firewall policy using the CLI. B. It represents the number of objects used in the firewall policy. C. It changes when firewall policies are reordered. D. It defines the order in which rules are processed.

An administrator does not want to report the logon events of service accounts to FortiGate. What setting on the collector agent is required to achieve this?. A. Add the support of NTLM authentication. B. Add user accounts to Active Directory (AD). C. Add user accounts to the FortiGate group fitter. D. Add user accounts to the Ignore User List.

Which two statements are true about the FGCP protocol? (Choose two.). A. FGCP elects the primary FortiGate device. B. FGCP is not used when FortiGate is in transparent mode. C. FGCP runs only over the heartbeat links. D. FGCP is used to discover FortiGate devices in different HA groups.

Which statement is correct regarding the inspection of some of the services available by web applications embedded in third-party websites?. A. The security actions applied on the web applications will also be explicitly applied on the thirdparty websites. B. The application signature database inspects traffic only from the original web application server. C. FortiGuard maintains only one signature of each web application that is unique. D. FortiGate can inspect sub-application traffic regardless where it was originated.

Which CLI command allows administrators to troubleshoot Layer 2 issues, such as an IP address conflict?. A. get system status. B. get system performance status. C. diagnose sys top. D. get system arp.

Which two settings can be separately configured per VDOM on a FortiGate device? (Choose two.). A. System time. B. FortiGuaid update servers. C. Operating mode. D. NGFW mode.

Which two statements about FortiGate FSSO agentless polling mode are true? (Choose two.). A. FortiGate uses the AD server as the collector agent. B. FortiGate uses the SMB protocol to read the event viewer logs from the DCs. C. FortiGate does not support workstation check . D. FortiGate directs the collector agent to use a remote LDAP server.

Refer to the exhibit. Which contains a session list output. Based on the information shown in the exhibit, which statement is true?. A. Destination NAT is disabled in the firewall policy. B. One-to-one NAT IP pool is used in the firewall policy. C. Overload NAT IP pool is used in the firewall policy. D. Port block allocation IP pool is used in the firewall policy.

How does FortiGate act when using SSL VPN in web mode?. A. FortiGate acts as an FDS server. B. FortiGate acts as an HTTP reverse proxy. C. FortiGate acts as DNS server. D. FortiGate acts as router.

Which two inspection modes can you use to configure a firewall policy on a profile-based nextgeneration firewall (NGFW)? (Choose two.). A. Proxy-based inspection. B. Certificate inspection. C. Flow-based inspection. D. Full Content inspection.

Refer to the exhibit. Examine the intrusion prevention system (IPS) diagnostic command. Which statement is correct If option 5 was used with the IPS diagnostic command and the outcome was a decrease in the CPU usage?. A. The IPS engine was inspecting high volume of traffic. B. The IPS engine was unable to prevent an intrusion attack . C. The IPS engine was blocking all traffic. D. The IPS engine will continue to run in a normal state.

Refer to the exhibits. The exhibits show the SSL and authentication policy (Exhibit A) and the security policy (Exhibit B) for Facebook . Users are given access to the Facebook web application. They can play video content hosted on Facebook but they are unable to leave reactions on videos or other types of posts. Which part of the policy configuration must you change to resolve the issue?. A. Make SSL inspection needs to be a deep content inspection. B. Force access to Facebook using the HTTP service. C. Get the additional application signatures are required to add to the security policy. D. Add Facebook in the URL category in the security policy.

Refer to the exhibit. The Root and To_Internet VDOMs are configured in NAT mode. The DMZ and Local VDOMs are configured in transparent mode. The Root VDOM is the management VDOM. The To_Internet VDOM allows LAN users to access the internet. The To_Internet VDOM is the only VDOM with internet access and is directly connected to ISP modem. With this configuration, which statement is true?. A. Inter-VDOM links are required to allow traffic between the Local and Root VDOMs. B. A static route is required on the To_Internet VDOM to allow LAN users to access the internet. C. Inter-VDOM links are required to allow traffic between the Local and DMZ VDOMs. D. Inter-VDOM links are not required between the Root and To_Internet VDOMs because the Root VDOM is used only as a management VDOM.

Which two statements explain antivirus scanning modes? (Choose two.). A. In proxy-based inspection mode, files bigger than the buffer size are scanned. B. In flow-based inspection mode, FortiGate buffers the file, but also simultaneously transmits it to the client. C. In proxy-based inspection mode, antivirus scanning buffers the whole file for scanning, before sending it to the client. D. In flow-based inspection mode, files bigger than the buffer size are scanned.

Which three statements explain a flow-based antivirus profile? (Choose three.). A. IPS engine handles the process as a standalone. B. FortiGate buffers the whole file but transmits to the client simultaneously. C. If the virus is detected, the last packet is delivered to the client. D. Optimized performance compared to proxy-based inspection. E. Flow-based inspection uses a hybrid of scanning modes available in proxy-based inspection.

Refer to the exhibit. The global settings on a FortiGate device must be changed to align with company security policies. What does the Administrator account need to access the FortiGate global settings?. A. Change password. B. Enable restrict access to trusted hosts. C. Change Administrator profile. D. Enable two-factor authentication.

Why does FortiGate Keep TCP sessions in the session table for several seconds, even after both sides (client and server) have terminated the session?. A. To allow for out-of-order packets that could arrive after the FIN/ACK packets. B. To finish any inspection operations. C. To remove the NAT operation. D. To generate logs.

Which statement about video filtering on FortiGate is true?. A. Full SSL Inspection is not required. B. It is available only on a proxy-based firewall policy. C. It inspects video files hosted on file sharing services. D. Video filtering FortiGuard categories are based on web filter FortiGuard categories.

Refer to the exhibit. Given the routing database shown in the exhibit, which two statements are correct? (Choose two.). A. The port3 default route has the highest distance. B. The port3 default route has the lowest metric. C. There will be eight routes active in the routing table. D. The port1 and port2 default routes are active in the routing table.

Refer to the web filter raw logs. Based on the raw logs shown in the exhibit, which statement is correct?. A. Social networking web filter category is configured with the action set to authenticate. B. The action on firewall policy ID 1 is set to warning. C. Access to the social networking web filter category was explicitly blocked to all users. D. The name of the firewall policy is all_users_web.

Refer to the exhibit. The exhibit shows the IPS sensor configuration. If traffic matches this IPS sensor, which two actions is the sensor expected to take? (Choose two.). A. The sensor will allow attackers matching the Microsoft Windows.iSCSI.Target.DoS signature. B. The sensor will block all attacks aimed at Windows servers. C. The sensor will reset all connections that match these signatures. D. The sensor will gather a packet log for all matched traffic.

When configuring a firewall virtual wire pair policy, which following statement is true?. A. Any number of virtual wire pairs can be included, as long as the policy traffic direction is the same. B. Only a single virtual wire pair can be included in each policy. C. Any number of virtual wire pairs can be included in each policy, regardless of the policy traffic direction settings. D. Exactly two virtual wire pairs need to be included in each policy.

An administrator is configuring an IPsec VPN between site A and site B. The Remote Gateway setting in both sites has been configured as Static IP Address. For site A, the local quick mode selector is 192. 168. 1.0/24 and the remote quick mode selector is 192. 168.2.0/24. Which subnet must the administrator configure for the local quick mode selector for site B?. A. 192. 168. 1.0/24. B. 192. 168.0.0/24. C. 192. 168.2.0/24. D. 192. 168.3.0/24.

An administrator wants to configure timeouts for users. Regardless of the userTMs behavior, the timer should start as soon as the user authenticates and expire after the configured value. Which timeout option should be configured on FortiGate?. A. auth-on-demand. B. soft-timeout. C. idle-timeout. D. new-session. E. hard-timeout.

Refer to the exhibit. Given the security fabric topology shown in the exhibit, which two statements are true? (Choose two.). A. There are five devices that are part of the security fabric. B. Device detection is disabled on all FortiGate devices. C. This security fabric topology is a logical topology view. D. There are 19 security recommendations for the security fabric.

A network administrator wants to set up redundant IPsec VPN tunnels on FortiGate by using two IPsec VPN tunnels and static routes. * All traffic must be routed through the primary tunnel when both tunnels are up * The secondary tunnel must be used only if the primary tunnel goes down * In addition, FortiGate should be able to detect a dead tunnel to speed up tunnel failover Which two key configuration changes are needed on FortiGate to meet the design requirements? (Choose two). A. Configure a high distance on the static route for the primary tunnel, and a lower distance on the static route for the secondary tunnel. B. Enable Dead Peer Detection. C. Configure a lower distance on the static route for the primary tunnel, and a higher distance on the static route for the secondary tunnel. D. Enable Auto-negotiate and Autokey Keep Alive on the phase 2 configuration of both tunnels.

Which two protocols are used to enable administrator access of a FortiGate device? (Choose two.). A. SSH. B. HTTPS. C. FTM. D. FortiTelemetry.

Incorreto A network administrator has enabled SSL certificate inspection and antivirus on FortiGate. When downloading an EICAR test file through HTTP, FortiGate detects the virus and blocks the file. When downloading the same file through HTTPS, FortiGate does not detect the virus and the file can be downloaded. What is the reason for the failed virus detection by FortiGate? (Choose two). A. The website is exempted from SSL inspection. B. The EICAR test file exceeds the protocol options oversize limit. C. The selected SSL inspection profile has certificate inspection enabled. D. The browser does not trust the FortiGate self-signed CA certificate.

Refer to the exhibit. Which contains a session diagnostic output. Which statement is true about the session diagnostic output?. A. The session is in SYN_SENT state. B. The session is in FIN_ACK state. C. The session is in FTN_WAIT state. D. The session is in ESTABLISHED state.

Refer to the exhibit. Review the Intrusion Prevention System (IPS) profile signature settings. Which statement is correct in adding the FTP.Login.Failed signature to the IPS sensor profile?. A. The signature setting uses a custom rating threshold. B. The signature setting includes a group of other signatures. C. Traffic matching the signature will be allowed and logged. D. Traffic matching the signature will be silently dropped and logged.

Refer to the exhibit. The exhibit contains a network diagram, virtual IP, IP pool, and firewall policies configuration. The WAN (port1) interface has the IP address 10.200. 1. 1/24. The LAN (port3) interface has the IP address 10 .0.1.254. /24. The first firewall policy has NAT enabled using IP Pool. The second firewall policy is configured with a VIP as the destination address. Which IP address will be used to source NAT the internet traffic coming from a workstation with the IP address 10.0. 1. 10?. A. 10.200.1.1. B. 10.200.3.1. C. 10.200.1.100. D. 10.200.1.10.

FortiGuard categories can be overridden and defined in different categories. To create a web rating override for example.com home page, the override must be configured using a specific syntax. Which two syntaxes are correct to configure web rating for the home page? (Choose two.). A. www.example.com:443. B. www.example.com. C. example.com. D. www.example.com/index.html.

Refer to the exhibits. An administrator creates a new address object on the root FortiGate (Local-FortiGate) in the security fabric. After synchronization, this object is not available on the downstream FortiGate (ISFW). What must the administrator do to synchronize the address object?. A. Change the csf setting on Local-FortiGate (root) to set configuration-sync local. B. Change the csf setting on ISFW (downstream) to set configuration-sync local. C. Change the csf setting on Local-FortiGate (root) to set fabric-object-unification default. D. Change the csf setting on ISFW (downstream) to set fabric-object-unification default.

Refer to the exhibit. Given the interfaces shown in the exhibit. which two statements are true? (Choose two.). A. Traffic between port2 and port2-vlan1 is allowed by default. B. port1-vlan10 and port2-vlan10 are part of the same broadcast domain. C. port1 is a native VLAN. D. port1-vlan and port2-vlan1 can be assigned in the same VDOM or to different VDOMs.

Refer to the exhibit. The exhibit contains the configuration for an SD-WAN Performance SLA, as well as the output of diagnose sys virtual-wan-link health-check . Which interface will be selected as an outgoing interface?. A. port2. B. port4. C. port3. D. port1.

Refer to the exhibit. An administrator is running a sniffer command as shown in the exhibit. Which three pieces of information are included in the sniffer output? (Choose three.). A. Interface name. B. Ethernet header. C. IP header. D. Application header. E. Packet payload.

Which two attributes are required on a certificate so it can be used as a CA certificate on SSL Inspection? (Choose two.). A. The keyUsage extension must be set to keyCertSign. B. The common name on the subject field must use a wildcard name. C. The issuer must be a public CA. D. The CA extension must be set to TRUE.

Refer to the exhibits. The SSL VPN connection fails when a user attempts to connect to it. What should the user do to successfully connect to SSL VPN?. A. Change the SSL VPN port on the client. B. Change the Server IP address. C. Change the idle-timeout. D. Change the SSL VPN portal to the tunnel.

Which two settings are required for SSL VPN to function between two FortiGate devices? (Choose two.). A. The client FortiGate requires a client certificate signed by the CA on the server FortiGate. B. The client FortiGate requires a manually added route to remote subnets. C. The client FortiGate uses the SSL VPN tunnel interface type to connect SSL VPN. D. The server FortiGate requires a CA certificate to verify the client FortiGate certificate.

An administrator has configured a strict RPF check on FortiGate. Which statement is true about the strict RPF check?. A. The strict RPF check is run on the first sent and reply packet of any new session. B. Strict RPF checks the best route back to the source using the incoming interface. C. Strict RPF checks only for the existence of at least one active route back to the source using the incoming interface. D. Strict RPF allows packets back to sources with all active routes.

Refer to the exhibits to view the firewall policy (Exhibit A) and the antivirus profile (Exhibit B). Which statement is correct if a user is unable to receive a block replacement message when downloading an infected file for the first time?. A. The firewall policy performs the full content inspection on the file. B. The flow-based inspection is used, which resets the last packet to the user. C. The volume of traffic being inspected is too high for this model of FortiGate. D. The intrusion prevention security profile needs to be enabled when using flow-based inspection mode.

An administrator wants to configure Dead Peer Detection (DPD) on IPSEC VPN for detecting dead tunnels. The requirement is that FortiGate sends DPD probes only when no traffic is observed in the tunnel. Which DPD mode on FortiGate will meet the above requirement?. A. Disabled. B. On Demand. C. Enabled. D. On Idle.

Refer to the exhibit showing a debug flow output. Which two statements about the debug flow output are correct? (Choose two.). A. The debug flow is of ICMP traffic. B. A firewall policy allowed the connection. C. A new traffic session is created. D. The default route is required to receive a reply.

Refer to the exhibit, which contains a session diagnostic output. Which statement is true about the session diagnostic output?. A. The session is a UDP unidirectional state. B. The session is in TCP ESTABLISHED state. C. The session is a bidirectional UDP connection. D. The session is a bidirectional TCP connection.

Which two statements are correct regarding FortiGate HA cluster virtual IP addresses? (Choose two.). A. Heartbeat interfaces have virtual IP addresses that are manually assigned. B. A change in the virtual IP address happens when a FortiGate device joins or leaves the cluster. C. Virtual IP addresses are used to distinguish between cluster members. D. The primary device in the cluster is always assigned IP address 169.254.0.1.

The HTTP inspection process in web filtering follows a specific order when multiple features are enabled in the web filter profile. What order must FortiGate use when the web filter profile has features enabled, such as safe search?. A. DNS-based web filter and proxy-based web filter. B. Static URL filter, FortiGuard category filter, and advanced filters. C. Static domain filter, SSL inspection filter, and external connectors filters. D. FortiGuard category filter and rating filter.

If Internet Service is already selected as Source in a firewall policy, which other configuration objects can be added to the Source filed of a firewall policy?. A. IP address. B. Once Internet Service is selected, no other object can be added. C. User or User Group. D. FQDN address.

Which statement about the IP authentication header (AH) used by IPsec is true?. A. AH does not provide any data integrity or encryption. B. AH does not support perfect forward secrecy. C. AH provides data integrity bur no encryption. D. AH provides strong data integrity but weak encryption.

When a firewall policy is created, which attribute is added to the policy to support recording logs to a FortiAnalyzer or a FortiManager and improves functionality when a FortiGate is integrated with these devices?. A. Log ID. B. Universally Unique Identifier. C. Policy ID. D. Sequence ID.

Which statements about the firmware upgrade process on an active-active HA cluster are true? (Choose two.). A. The firmware image must be manually uploaded to each FortiGate. B. Only secondary FortiGate devices are rebooted. C. Uninterruptable upgrade is enabled by default. D. Traffic load balancing is temporally disabled while upgrading the firmware.

Which two statements ate true about the Security Fabric rating? (Choose two.). A. It provides executive summaries of the four largest areas of security focus. B. Many of the security issues can be fixed immediately by clicking Apply where available. C. The Security Fabric rating must be run on the root FortiGate device in the Security Fabric. D. The Security Fabric rating is a free service that comes bundled with alt FortiGate devices.

An administrator has configured two-factor authentication to strengthen SSL VPN access. Which additional best practice can an administrator implement?. A. Configure Source IP Pools. B. Configure split tunneling in tunnel mode. C. Configure different SSL VPN realms. D. Configure host check .

Which of the following conditions must be met in order for a web browser to trust a web server certificate signed by a third-party CA?. A. The public key of the web server certificate must be installed on the browser. B. The web-server certificate must be installed on the browser. C. The CA certificate that signed the web-server certificate must be installed on the browser. D. The private key of the CA certificate that signed the browser certificate must be installed on the.

A network administrator is troubleshooting an IPsec tunnel between two FortiGate devices. The administrator has determined that phase 1 fails to come up. The administrator has also re-entered the pre-shared key on both FortiGate devices to make sure they match. Based on the phase 1 configuration and the diagram shown in the exhibit, which two configuration changes will bring phase 1 up? (Choose two.). A. On HQ-FortiGate, set IKE mode to Main (ID protection). B. On both FortiGate devices, set Dead Peer Detection to On Demand. C. On HQ-FortiGate, disable Diffie-Helman group 2. D. On Remote-FortiGate, set port2 as Interface.

Which of the following are purposes of NAT traversal in IPsec? (Choose two.). A. To detect intermediary NAT devices in the tunnel path. B. To dynamically change phase 1 negotiation mode aggressive mode. C. To encapsulation ESP packets in UDP packets using port 4500. D. To force a new DH exchange with each phase 2 rekey.

An administrator has a requirement to keep an application session from timing out on port 80. What two changes can the administrator make to resolve the issue without affecting any existing services running through FortiGate? (Choose two.). A. Create a new firewall policy with the new HTTP service and place it above the existing HTTP policy. B. Create a new service object for HTTP service and set the session TTL to never. C. Set the TTL value to never under config system-ttl. D. Set the session TTL on the HTTP policy to maximum.

A team manager has decided that, while some members of the team need access to a particular website, the majority of the team does not Which configuration option is the most effective way to support this request?. A. Implement a web filter category override for the specified website. B. Implement a DNS filter for the specified website. C. Implement web filter quotas for the specified website. D. Implement web filter authentication for the specified website.

A network administrator has enabled full SSL inspection and web filtering on FortiGate. When visiting any HTTPS websites, the browser reports certificate warning errors. When visiting HTTP websites, the browser does not report errors. What is the reason for the certificate warning errors?. A. The browser requires a software update. B. FortiGate does not support full SSL inspection when web filtering is enabled. C. The CA certificate set on the SSL/SSH inspection profile has not been imported into the browser. D. There are network connectivity issues.

Which certificate value can FortiGate use to determine the relationship between the issuer and the certificate?. A. Subject Key Identifier value. B. SMMIE Capabilities value. C. Subject valueC. Subject value. D. Subject Alternative Name value.

Which two statements are true about the RPF check? (Choose two.). A. The RPF check is run on the first sent packet of any new session. B. The RPF check is run on the first reply packet of any new session. C. The RPF check is run on the first sent and reply packet of any new session. D. RPF is a mechanism that protects FortiGate and your network from IP spoofing attacks.

Which two protocol options are available on the CLI but not on the GUI when configuring an SD-WAN Performance SLA? (Choose two.). A. DNS. B. ping. C. udp-echo. D. TWAMP.

An administrator needs to configure VPN user access for multiple sites using the same soft FortiToken. Each site has a FortiGate VPN gateway. What must an administrator do to achieve this objective?. A. The administrator can register the same FortiToken on more than one FortiGate. B. The administrator must use a FortiAuthenticator device. C. The administrator can use a third-party radius OTP server. D. The administrator must use the user self-registration server.

Which two statements are true when FortiGate is in transparent mode? (Choose two.). A. By default, all interfaces are part of the same broadcast domain. B. The existing network IP schema must be changed when installing a transparent mode. C. Static routes are required to allow traffic to the next hop. D. FortiGate forwards frames without changing the MAC address.

Which three CLI commands can you use to troubleshoot Layer 3 issues if the issue is in neither the physical layer nor the link layer? (Choose three.). A. diagnose sys top. B. execute ping. C. execute traceroute. D. diagnose sniffer packet any. E. get system arp.

Examine this PAC file configuration. Which of the following statements are true? (Choose two.). A. Browsers can be configured to retrieve this PAC file from the FortiGate. B. Any web request to the 172.25. 120.0/24 subnet is allowed to bypass the proxy. C. All requests not made to Fortinet.com or the 172.25. 120.0/24 subnet, have to go through altproxy.corp.com: 8060. D. Any web request fortinet.com is allowed to bypass the proxy.

If the Issuer and Subject values are the same in a digital certificate, which type of entity was the certificate issued to?. A. A CRL. B. A person. C. A subordinate CA. D. A root CA.

Which three statements are true regarding session-based authentication? (Choose three.). A. HTTP sessions are treated as a single user. B. IP sessions from the same source IP address are treated as a single user. C. It can differentiate among multiple clients behind the same source IP address. D. It requires more resources. E. It is not recommended if multiple users are behind the source NAT.

Which statement regarding the firewall policy authentication timeout is true?. A. It is an idle timeout. The FortiGate considers a user to be "idle" if it does not see any packets coming from the user's source IP. B. It is a hard timeout. The FortiGate removes the temporary policy for a user's source IP address after this timer has expired. C. It is an idle timeout. The FortiGate considers a user to be "idle" if it does not see any packets coming from the user's source MAC. D. It is a hard timeout. The FortiGate removes the temporary policy for a user's source MAC address after this timer has expired.

Which of statement is true about SSL VPN web mode?. A. The tunnel is up while the client is connected. B. It supports a limited number of protocols. C. The external network application sends data through the VPN. D. It assigns a virtual IP address to the client.

What inspection mode does FortiGate use if it is configured as a policy-based next-generation firewall (NGFW)?. A. Full Content inspection. B. Proxy-based inspection. C. Certificate inspection. D. Flow-based inspection.

Which of the following are valid actions for FortiGuard category based filter in a web filter profile ui proxy-based inspection mode? (Choose two.). A. Warning. B. Exempt. C. Allow. D. Learn.

Which two types of traffic are managed only by the management VDOM? (Choose two.). A. FortiGuard web filter queries. B. PKI. C. Traffic shaping. D. DNS.

Which of the following statements is true regarding SSL VPN settings for an SSL VPN portal?. A. By default, FortiGate uses WINS servers to resolve names. B. By default, the SSL VPN portal requires the installation of a client's certificate. C. By default, split tunneling is enabled. D. By default, the admin GUI and SSL VPN portal use the same HTTPS port.

Refer to the exhibits. The exhibits show the firewall policies and the objects used in the firewall policies. The administrator is using the Policy Lookup feature and has entered the search criteria shown in the exhibit. Which policy will be highlighted, based on the input criteria?. A. Policy with ID 4. B. Policy with ID 5. C. Policies with ID 2 and 3. D. Policy with ID 4.

Which statement correctly describes the use of reliable logging on FortiGate?. A. Reliable logging is enabled by default in all configuration scenarios. B. Reliable logging is required to encrypt the transmission of logs. C. Reliable logging can be configured only using the CLI. D. Reliable logging prevents the loss of logs when the local disk is full.

Refer to the exhibit. The exhibit shows a diagram of a FortiGate device connected to the network, the firewall policy and VIP configuration on the FortiGate device, and the routing table on the ISP router. When the administrator tries to access the web server public address (203.0.113.2) from the internet, the connection times out. At the same time, the administrator runs a sniffer on FortiGate to capture incoming web traffic to the server and does not see any output. Based on the information shown in the exhibit, what configuration change must the administrator make to fix the connectivity issue?. A. Configure a loopback interface with address 203.0.113.2/32. B. In the VIP configuration, enable arp-reply. C. Enable port forwarding on the server to map the external service port to the internal service port. D. In the firewall policy configuration, enable match-vip.

What are two benefits of flow-based inspection compared to proxy-based inspection? (Choose two.). A. FortiGate uses fewer resources. B. FortiGate performs a more exhaustive inspection on traffic. C. FortiGate adds less latency to traffic. D. FortiGate allocates two sessions per connection.

Refer to exhibit. An administrator configured the web filtering profile shown in the exhibit to block access to all social networking sites except Twitter. However, when users try to access twitter.com, they are redirected to a FortiGuard web filtering block page. Based on the exhibit, which configuration change can the administrator make to allow Twitter while blocking all other social networking sites?. A. On the FortiGuard Category Based Filter configuration, set Action to Warning for Social Networking. B. On the Static URL Filter configuration, set Type to Simple. C. On the Static URL Filter configuration, set Action to Exempt. D. On the Static URL Filter configuration, set Action to Monitor.

What are two functions of ZTNA? (Choose two.). A. ZTNA manages access through the client only. B. ZTNA manages access for remote users only. C. ZTNA provides a security posture check. D. ZTNA provides role-based access.

Which timeout setting can be responsible for deleting SSL VPN associated sessions?. A. SSL VPN idle-timeout. B. SSL VPN http-request-body-timeout. C. SSL VPN login-timeout. D. SSL VPN dtls-hello-timeout.

Which statement is correct regarding the use of application control for inspecting web applications?. A. Application control can identify child and parent applications, and perform different actions on them. B. Application control signatures are organized in a nonhierarchical structure. C. Application control does not require SSL inspection to identity web applications. D. Application control does not display a replacement message for a blocked web application.

Refer to the exhibits. Exhibit A shows a topology for a FortiGate HA cluster that performs proxy-based inspection on traffic. Exhibit B shows the HA configuration and the partial output of the get system ha status command. Based on the exhibits, which two statements about the traffic passing through the cluster are true? (Choose two.). A. For non-load balanced connections, packets forwarded by the cluster to the server contain the virtual MAC address of port2 as source. B. The traffic sourced from the client and destined to the server is sent to FGT-1. C. The cluster can load balance ICMP connections to the secondary. D. For load balanced connections, the primary encapsulates TCP SYN packets before forwarding them to the secondary.

Refer to the exhibit. Based on the ZTNA tag, the security posture of the remote endpoint has changed. What will happen to endpoint active ZTNA sessions?. A. They will be re-evaluated to match the endpoint policy. B. They will be re-evaluated to match the firewall policy. C. They will be re-evaluated to match the ZTNA policy. D. They will be re-evaluated to match the security policy.

Refer to the exhibit. The exhibit shows a diagram of a FortiGate device connected to the network and the firewall policy and IP pool configuration on the FortiGate device. Which two actions does FortiGate take on internet traffic sourced from the subscribers? (Choose two.). A. FortiGate allocates port blocks per user, based on the configured range of internal IP addresses. B. FortiGate allocates port blocks on a first-come, first-served basis. C. FortiGate generates a system event log for every port block allocation made per user. D. FortiGate allocates 128 port blocks per user.

Which statement about video filtering on FortiGate is true?. A. Video filtering FortiGuard categories are based on web filter FortiGuard categories. B. It does not require a separate FortiGuard license. C. Full SSL inspection is not required. D. It is available only on a proxy-based firewall policy.

Which statement describes a characteristic of automation stitches?. A. They can have one or more triggers. B. They can be run only on devices in the Security Fabric. C. They can run multiple actions simultaneously. D. They can be created on any device in the fabric.

Refer to the exhibits. Exhibit A shows a network diagram. Exhibit B shows the firewall policy configuration and a VIP object configuration. The WAN (port1) interface has the IP address 10.200.1.1/24. The LAN (port3) interface has the IP address 10.0.1.254/24. If the host 10.200.3.1 sends a TCP SYN packet on port 10443 to 10.200.1.10, what will the source address, destination address, and destination port of the packet be, after FortiGate forwards the packet to the destination?. A. 10.0.1.254, 10.0.1.10, and 443, respectively. B. 10.0.1.254, 10.0.1.10, and 10443, respectively. C. 10.200.3.1, 10.0.1.10, and 443, respectively.

Refer to the exhibit. The exhibit shows the output of a diagnose command. What does the output reveal about the policy route?. A. It is an ISDB route in policy route. B. It is a regular policy route. C. It is an ISDB policy route with an SDWAN rule. D. It is an SDWAN rule in policy route.

Refer to the exhibit. A network administrator is troubleshooting an IPsec tunnel between two FortiGate devices. The administrator has determined that phase 1 status is up, but phase 2 fails to come up. Based on the phase 2 configuration shown in the exhibit, which configuration change will bring phase 2 up?. A. On Remote-FortiGate, set Seconds to 43200. B. On HQ-FortiGate, set Encryption to AES256. C. On HQ-FortiGate, enable Diffie-Hellman Group 2. D. On HQ-FortiGate, enable Auto-negotiate.

An administrator configures FortiGuard servers as DNS servers on FortiGate using default settings. What is true about the DNS connection to a FortiGuard server?. A. It uses UDP 8888. B. It uses UDP 53. C. It uses DNS over HTTPS. D. It uses DNS overTLS.

Which three methods are used by the collector agent for AD polling? (Choose three.). A. FortiGate polling. B. NetAPI. C. Novell API. D. WMI. E. WinSecLog.

Which three authentication timeout types are availability for selection on FortiGate? (Choose three.). A. hard-timeout. B. auth-on-demand. C. soft-timeout. D. new-session. E. Idle-timeout.

Refer to the exhibit. A network administrator is troubleshooting an IPsec tunnel between two FortiGate devices. The administrator has determined that phase 1 status is up. but phase 2 fails to come up. Based on the phase 2 configuration shown in the exhibit, what configuration change will bring phase 2 up?. A. On HQ-FortiGate, enable Auto-negotiate. B. On Remote-FortiGate, set Seconds to 43200. C. On HQ-FortiGate, enable Diffie-Hellman Group 2. D. On HQ-FortiGate, set Encryption to AES256.

Which three options are the remote log storage options you can configure on FortiGate? (Choose three.). A. FortiCache. B. FortiSIEM. C. FortiAnalyzer. D. FortiSandbox. E. FortiCloud.

A network administrator is configuring a new IPsec VPN tunnel on FortiGate. The remote peer IP address is dynamic. In addition, the remote peer does not support a dynamic DNS update service. What type of remote gateway should the administrator configure on FortiGate for the new IPsec VPN tunnel to work?. A. Static IP Address. B. Dialup User. C. Dynamic DNS. D. Pre-shared Key.

An administrator has configured outgoing Interface any in a firewall policy. Which statement is true about the policy list view?. A. Policy lookup will be disabled. B. By Sequence view will be disabled. C. Search option will be disabled. D. Interface Pair view will be disabled.

Which statement correctly describes NetAPI polling mode for the FSSO collector agent?. A. The collector agent uses a Windows API to query DCs for user logins. B. NetAPI polling can increase bandwidth usage in large networks. C. The collector agent must search security event logs. D. The NetSession Enum function is used to track user logouts.

An administrator has configured the following settings: What are the two results of this configuration? (Choose two.). A. Device detection on all interfaces is enforced for 30 minutes. B. Denied users are blocked for 30 minutes. C. A session for denied traffic is created. D. The number of logs generated by denied traffic is reduced.

In an explicit proxy setup, where is the authentication method and database configured?. A. Proxy Policy. B. Authentication Rule. C. Firewall Policy. D. Authentication scheme.

In consolidated firewall policies, IPv4 and IPv6 policies are combined in a single consolidated policy. Instead of separate policies. Which three statements are true about consolidated IPv4 and IPv6 policy configuration? (Choose three.). A. The IP version of the sources and destinations in a firewall policy must be different. B. The Incoming Interface. Outgoing Interface. Schedule, and Service fields can be shared with both IPv4 and IPv6. C. The policy table in the GUI can be filtered to display policies with IPv4, IPv6 or IPv4 and IPv6 sources and destinations. D. The IP version of the sources and destinations in a policy must match. E. The policy table in the GUI will be consolidated to display policies with IPv4 and IPv6 sources and destinations.

Which of the following are valid actions for FortiGuard category based filter in a web filter profile ui proxy-based inspection mode? (Choose two.). A. Warning. B. Exempt. C. Allow. D. Learn.

Examine this FortiGate configuration: How does the FortiGate handle web proxy traffic coming from the IP address 10.2.1.200 that requires authorization?. A. It always authorizes the traffic without requiring authentication. B. It drops the traffic. C. It authenticates the traffic using the authentication scheme SCHEME2. D. It authenticates the traffic using the authentication scheme SCHEME1.

Which two types of traffic are managed only by the management VDOM? (Choose two.). A. FortiGuard web filter queries. B. PKI. C. Traffic shaping. D. DNS.

Refer to the exhibit. Which contains a network diagram and routing table output. The Student is unable to access Webserver. What is the cause of the problem and what is the solution for the problem?. A. The first packet sent from Student failed the RPF check.This issue can be resolved by adding a static route to 10.0.4.0/24 through wan1. B. The first reply packet for Student failed the RPF check.This issue can be resolved by adding a static route to 10.0.4.0/24 through wan1. C. The first reply packet for Student failed the RPF check .This issue can be resolved by adding a static route to 203.0. 114.24/32 through port3. D. The first packet sent from Student failed the RPF check.This issue can be resolved by adding a static route to 203.0. 114.24/32 through port3.

Which CLI command will display sessions both from client to the proxy and from the proxy to the servers?. A. diagnose wad session list. B. diagnose wad session list | grep hook-pre&&hook-out. C. diagnose wad session list | grep hook=pre&&hook=out. D. diagnose wad session list | grep "hook=pre"&"hook=out".

Which three criteria can a FortiGate use to look for a matching firewall policy to process traffic? (Choose three.). A. Source defined as Internet Services in the firewall policy. B. Destination defined as Internet Services in the firewall policy. C. Highest to lowest priority defined in the firewall policy. D. Services defined in the firewall policy. E. Lowest to highest policy ID number.

Which scanning technique on FortiGate can be enabled only on the CLI?. A. Heuristics scan (Or Machine learning scan). B. Trojan scan. C. Antivirus scan. D. Ransomware scan.

Refer to the exhibit to view the application control profile. Based on the configuration, what will happen to Apple FaceTime?. A. Apple FaceTime will be blocked, based on the Excessive-Bandwidth filter configuration. B. Apple FaceTime will be allowed, based on the Apple filter configuration. C. Apple FaceTime will be allowed only if the filter in Application and Filter Overrides is set to Learn. D. Apple FaceTime will be allowed, based on the Categories configuration.

An administrator must disable RPF check to investigate an issue. Which method is best suited to disable RPF without affecting features like antivirus and intrusion prevention system?. A. Enable asymmetric routing, so the RPF check will be bypassed. B. Disable the RPF check at the FortiGate interface level for the source check. C. Disable the RPF check at the FortiGate interface level for the reply check . D. Enable asymmetric routing at the interface level.

An administrator is configuring an Ipsec between site A and site B. The Remotes Gateway setting in both sites has been configured as Static IP Address. For site A, the local quick mode selector is 192. 16.1.0/24 and the remote quick mode selector is 192.16.2.0/24. How must the administrator configure the local quick mode selector for site B?. A. 192.168.3.0/24. B. 192.168.2.0/24. C. 192.168. 1.0/24. D. 192.168.0.0/8.

Which of the following statements about central NAT are true? (Choose two.). A. IP pool references must be removed from existing firewall policies before enabling central NAT . B. Central NAT can be enabled or disabled from the CLI only. C. Source NAT, using central NAT, requires at least one central SNAT policy. D. Destination NAT, using central NAT, requires a VIP object as the destination address in a firewall.

An organization's employee needs to connect to the office through a high-latency internet connection. Which SSL VPN setting should the administrator adjust to prevent the SSL VPN negotiation failure?. A. Change the session-ttl. B. Change the login timeout. C. Change the idle-timeout. D. Change the udp idle timer.

An administrator observes that the port1 interface cannot be configured with an IP address. What can be the reasons for that? (Choose three.). A. The interface has been configured for one-arm sniffer. B. The interface is a member of a virtual wire pair. C. The operation mode is transparent. D. The interface is a member of a zone. E. Captive portal is enabled in the interface.

Which two statements are correct about a software switch on FortiGate? (Choose two.). A. It can be configured only when FortiGate is operating in NAT mode. B. Can act as a Layer 2 switch as well as a Layer 3 router. C. All interfaces in the software switch share the same IP address. D. It can group only physical interfaces.

Which two statements are correct regarding FortiGate FSSO agentless polling mode? (Choose two.). A. FortiGate points the collector agent to use a remote LDAP server. B. FortiGate uses the AD server as the collector agent. C. FortiGate uses the SMB protocol to read the event viewer logs from the DCs. D. FortiGate queries AD by using the LDAP to retrieve user group information.

What is the limitation of using a URL list and application control on the same firewall policy, in NGFW policy-based mode?. A. It limits the scope of application control to the browser-based technology category only. B. It limits the scope of application control to scan application traffic based on application category only. C. It limits the scope of application control to scan application traffic using parent signatures only. D. It limits the scope of application control to scan application traffic on DNS protocol only.

Examine this output from a debug flow: Why did the FortiGate drop the packet?. A. The next-hop IP address is unreachable. B. It failed the RPF check . C. It matched an explicitly configured firewall policy with the action DENY. D. It matched the default implicit firewall policy.

Which three security features require the intrusion prevention system (IPS) engine to function? (Choose three). A. Web filter in flow-based inspection. B. Antivirus in flow-based inspection. C. DNS filter. D. Web application firewall. E. Application control.

Which of the following statements about backing up logs from the CLI and downloading logs from the GUI are true? (Choose two.). A. Log downloads from the GUI are limited to the current filter view. B. Log backups from the CLI cannot be restored to another FortiGate. C. Log backups from the CLI can be configured to upload to FTP as a scheduled time. D. Log downloads from the GUI are stored as LZ4 compressed files.

An administrator needs to increase network bandwidth and provide redundancy. What interface type must the administrator select to bind multiple FortiGate interfaces?. A. VLAN interface. B. Software Switch interface. C. Aggregate interface. D. Redundant interface.

Refer to the exhibit. An administrator added a configuration for a new RADIUS server. While configuring, the administrator selected the Include in every user group option. What is the impact of using the Include in every user group option in a RADIUS configuration?. A. This option places the RADIUS server, and all users who can authenticate against that server, into every FortiGate user group. B. This option places all FortiGate users and groups required to authenticate into the RADIUS server, which, in this case, is FortiAuthenticator. C. This option places all users into every RADIUS user group, including groups that are used for the LDAP server on FortiGate. D. This option places the RADIUS server, and all users who can authenticate against that server, into every RADIUS group.

Refer to the exhibit. The exhibit contains a network diagram, central SNAT policy, and IP pool configuration. The WAN (port1) interface has the IP address 10.200.1.1/24. The LAN (port3) interface has the IP address 10.0.1.254/24. A firewall policy is configured to allow to destinations from LAN (port3) to WAN (port1). Central NAT is enabled, so NAT settings from matching Central SNAT policies will be applied. Which IP address will be used to source NAT the traffic, if the user on Local-Client (10.0. 1. 10) pings the IP address of Remote-FortiGate (10.200.3. 1)?. A. 10.200.1.149. B. 10.200.1.1. C. 10.200.1.49. D. 10.200.1.99.

Refer to the exhibit. Based on the administrator profile settings, what permissions must the administrator set to run the diagnose firewall auth list CLI command on FortiGate?. A. Custom permission for Network. B. Read/Write permission for Log & Report. C. CLI diagnostics commands permission. D. Read/Write permission for Firewall.

Refer to the exhibits. The exhibits show a network diagram and firewall configurations. An administrator created a Deny policy with default settings to deny Webserver access for Remote- User2. Remote-User1 must be able to access the Webserver. Remote-User2 must not be able to access the Webserver. In this scenario, which two changes can the administrator make to deny Webserver access for Remote-User2? (Choose two.). A. Disable match-vip in the Deny policy. B. Set the Destination address as Deny_IP in the Allow-access policy. C. Enable match vip in the Deny policy. D. Set the Destination address as Web_server in the Deny policy.

An administrator is running the following sniffer command: Which three pieces of Information will be Included in me sniffer output? {Choose three.). A. Interface name. B. Packet payload. C. Ethernet header. D. IP header. E. Application header.

Refer to the FortiGuard connection debug output. Based on the output shown in the exhibit, which two statements are correct? (Choose two.). A. A local FortiManager is one of the servers FortiGate communicates with. B. One server was contacted to retrieve the contract information. C. There is at least one server that lost packets consecutively. D. FortiGate is using default FortiGuard communication settings.

A FortiGate is operating in NAT mode and configured with two virtual LAN (VLAN) sub interfaces added to the physical interface. Which statements about the VLAN sub interfaces can have the same VLAN ID, only if they have IP addresses in different subnets. A. The two VLAN sub interfaces can have the same VLAN ID, only if they have IP addresses in different subnets. B. The two VLAN sub interfaces must have different VLAN IDs. C. The two VLAN sub interfaces can have the same VLAN ID, only if they belong to different VDOMs. D. The two VLAN sub interfaces can have the same VLAN ID, only if they have IP addresses in the same subnet.

Which of the following SD-WAN load balancing method use interface weight value to distribute traffic? (Choose two.). A. Source IP. B. Spillover. C. Volume. D. Session.

What is the effect of enabling auto-negotiate on the phase 2 configuration of an IPsec tunnel?. A. FortiGate automatically negotiates different local and remote addresses with the remote peer. B. FortiGate automatically negotiates a new security association after the existing security association expires. C. FortiGate automatically negotiates different encryption and authentication algorithms with the remote peer. D. FortiGate automatically brings up the IPsec tunnel and keeps it up, regardless of activity on the IPsec tunnel.

If the Services field is configured in a Virtual IP (VIP), which statement is true when central NAT is used?. A. The Services field prevents SNAT and DNAT from being combined in the same policy. B. The Services field is used when you need to bundle several VIPs into VIP groups. C. The Services field removes the requirement to create multiple VIPs for different services. D. The Services field prevents multiple sources of traffic from using multiple services to connect to a single computer.

In which two ways can RPF checking be disabled? (Choose two ). A. Enable anti-replay in firewall policy. B. Disable the RPF check at the FortiGate interface level for the source check. C. Enable asymmetric routing. D. Disable strict-arc-check under system settings.

Which feature in the Security Fabric takes one or more actions based on event triggers?. A. Fabric Connectors. B. Automation Stitches. C. Security Rating. D. Logical Topology.

Consider the topology: Application on a Windows machine <--{SSL VPN} -->FGT--> Telnet to Linux server. An administrator is investigating a problem where an application establishes a Telnet session to a Linux server over the SSL VPN through FortiGate and the idle session times out after about 90 minutes. The administrator would like to increase or disable this timeout. The administrator has already verified that the issue is not caused by the application or Linux server. This issue does not happen when the application establishes a Telnet connection to the Linux server directly on the LAN. What two changes can the administrator make to resolve the issue without affecting services running through FortiGate? (Choose two.). A. Set the maximum session TTL value for the TELNET service object. B. Set the session TTL on the SSLVPN policy to maximum, so the idle session timeout will not happen after 90 minutes. C. Create a new service object for TELNET and set the maximum session TTL. D. Create a new firewall policy and place it above the existing SSLVPN policy for the SSL VPN traffic, and set the new TELNET service object in the policy.

Which statements best describe auto discovery VPN (ADVPN). (Choose two.). A. It requires the use of dynamic routing protocols so that spokes can learn the routes to other spokes. B. ADVPN is only supported with IKEv2. C. Tunnels are negotiated dynamically between spokes. D. Every spoke requires a static tunnel to be configured to other spokes so that phase 1 and phase 2 proposals are defined in advance.

FortiGate is configured as a policy-based next-generation firewall (NGFW) and is applying web filtering and application control directly on the security policy. Which two other security profiles can you apply to the security policy? (Choose two.). A. Antivirus scanning. B. File filter. C. DNS filter. D. Intrusion prevention.

Refer to the exhibit. Based on the raw log, which two statements are correct? (Choose two.). A. Traffic is blocked because Action is set to DENY in the firewall policy. B. Traffic belongs to the root VDOM. C. This is a security log. D. Log severity is set to error on FortiGate.

To complete the final step of a Security Fabric configuration, an administrator must authorize all the devices on which device?. A. FortiManager. B. Root FortiGate. C. FortiAnalyzer. D. Downstream FortiGate.

View the exhibit. Which of the following statements are correct? (Choose two.). A. This setup requires at least two firewall policies with the action set to IPsec. B. Dead peer detection must be disabled to support this type of IPsec setup. C. The TunnelB route is the primary route for reaching the remote site. The TunnelA route is used only if the TunnelB VPN is down. D. This is a redundant IPsec setup.

Examine the exhibit, which contains a virtual IP and firewall policy configuration. The WAN (port1) interface has the IP address 10.200.1.1/24. The LAN (port2) interface has the IP address 10.0. 1.254/24. The first firewall policy has NAT enabled on the outgoing interface address. The second firewall policy is configured with a VIP as the destination address. Which IP address will be used to source NAT the Internet traffic coming from a workstation with the IP address 10.0. 1.10/24?. A. 10.200.1.10. B. Any available IP address in the WAN (port1) subnet 10.200.1.0/24. C. 10.200.1.1. D. 10.0.1.254.

Which two actions can you perform only from the root FortiGate in a Security Fabric? (Choose two.). A. Shut down/reboot a downstream FortiGate device. B. Disable FortiAnalyzer logging for a downstream FortiGate device. C. Log in to a downstream FortiSwitch device. D. Ban or unban compromised hosts.

What is the limitation of using a URL list and application control on the same firewall policy, in NGFW policy-based mode?. A. It limits the scanning of application traffic to the DNS protocol only. B. It limits the scanning of application traffic to use parent signatures only. C. It limits the scanning of application traffic to the browser-based technology category only. D. It limits the scanning of application traffic to the application category only.

You have enabled logging on your FortiGate device for Event logs and all Security logs, and you have set up logging to use the FortiGate local disk . What is the default behavior when the local disk is full?. A. Logs are overwritten and the only warning is issued when log disk usage reaches the threshold of 95%. B. No new log is recorded until you manually clear logs from the local disk . C. Logs are overwritten and the first warning is issued when log disk usage reaches the threshold of 75%. D. No new log is recorded after the warning is issued when log disk usage reaches the threshold of 95%.

Why does FortiGate keep TCP sessions in the session table for some seconds even after both sides (client and server) have terminated the session?. A. To remove the NAT operation. B. To generate logs. C. To finish any inspection operations. D. To allow for out-of-order packets that could arrive after the FIN/ACK packets.

Agora o 7 de 4 2. OK !. NO !.

An administrator must enabl DHCP server on one of the directly connected networks on FortiGate. However the adminstrator is unable to complete the process on the GUI to enable the service on the interface. In this scenario, what prevents the administrator from enabling DHCP service?. The FortiGate model does not support the DHCP server. Another interface is configured as the only DHCP server on FortiGate. The role of the interface prevents setting a DHCP server. The DHCP server setting is avaliable only on the CLI.

Refer to the exhibits. The exhibits show a diagram of a Fortigate device connected to the network, and the firewall configuration. An administrator created a Deny policy with default settings to deny Webserver while preventing Remote-User2 from acessing the Webserver. Which two configuration changes can the administrator make to the policy to deny Webserver access for Remote-user2? (Choose Two.). Enable Match-vip in the Deny policy. Set the Destination address as Webserver in the Deny policy. Set the Destination address as Deny_IP in the Allow_acess policy. Disable match-vip in the Deny policy.

Refer to the exhibit, which shows a partial configuration from the remote authentication server. Why does the Fortigate administrator need this configuration?. To set up a RADIUS server Secret. To authenticate and match the Training OU on the RADIUS server. to authenticate only the Training user group. To authenticate Any FortiGate user groups.

Refer to the exhibit. Which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules? (Implicit is source destination IP). All traffic from a source IP is sent to the same interface. Traffic is distributed base on the number of sessions throug each interface. Traffic is sent to the link with the lowest latency. All traffic from a source IP to a destination IP is sent to the same interface.

Refer to the exhibits. The exhibits show a diagram of a FortiGate device connected to the network, as well as the IP pool configuration and firewall policy objects. The WAN (port1) interface has the IP address 10.0.1.254/24. The LAN (port3) interface has the IP address 10.0.1.254/24. Which IP address will be used to source NAT (SNAT) the traffic, if the user on Local-Client(10.0.1.10) pings the IP address of Remote-FortiGate(10.200.3.1)?. 10.200.1.49. 10.200.1.49. 10.200.1.99. 10.200.1.1.

When FortiGate performs SSL/SSH full inspection, you can decide how it should react when it detects an invalid certificate. Which three actions are valid actions that Fortigate can perform when it detects an invalid certificate? (Choose three.). Block & Warning. Allow & Warning. Block. Trust & Allow. Allow.

A network administrator is configuring an IPsec. VPN tunnel for a sales employee travelling abroad. Which IPsec Wizard template must the adminstrator apply?. Site to Site. Hub-and-Spoke. Dial up User. Remote Access.

Refer to exhibits to view the firewall policy (Exhibit A) and the antivirus profile (Exhibit B). Exhibit A. Exhibit B. The intrusion prevention security profile must be enabled when using flow-based inspection mode. The firewall policy performs a full content inspection is enabled. The option to send files to FortiSandbox for inspection is enabled. Flow-based inspection is used, which resets the last packet to the user.

Refer to the exhibit to view the firewall policy. why would the firewall policy not block a well-know virus, for example eicar?. Web filter is not enabled on the firewall policy to complement the antivirus profile. The firewall policy is not configured in proxy-based inspection mode. The action on the firewall policy is not set to deny. The firewall policy does not apply deep content inspection.

Refer to the exhibits. FGT-1 and FGT-2 are updated with HA configuration commands show in the exhibit. what would be the expected outcome in the HA cluster?. FGT-1 will synchronize the override disable setting with FGT-2. The HA cluster will become out of sync because the override setting must match on all HA members. FGT-1 will remain the primary because FGT-2 has lower priority. FGT-2 will take over as the primary because it has override enable setting and higher priority than FGT-1.

FortiGate is integrated with FortiAnalyzer and FortiManager. When a firewall policy is created, which atribute is added to the policy to improve functionality and to support recording logs to FortiAnalyzer or FortiManager?. Log ID. Policy ID. Universally Unique Identifier. Sequence ID.

What is the common feature shared between IPv4 and SD-WAN ECMP algorithms?. Both use the same physical interface load balancing settings. Both control ECMP algorithms. Both support volume algorithms. Both can be enabled at the same time.

Refer to the exhibit. FortiGate has two separate firewall policies for Sales and Engineering to access the same web server with the same security profiles. Which action must the adminstrator perform to consolidate the two policies into one?. Enable Multiple Interface Policies to select port1 and port2 in the same firewall policy. Replace port1 and port2 with the any interface in a single firewall policy. Select port1 and port2 subnets in a single firewall policy. Create an Interface Group that includes port1 and port2 to create a single firewall policy.

An administrator needs to create a tunnel mode SSL-VPN to access an internal web server from the internet. The web server is connected to port1. The internet is connected to port2. Both interfaces belong to the VDOM named Corporation. What interface must the administrator use as the source for the firewall policy that will allow this traffic?. port1. ssl.root. port2. ssl.Corporation.

An administrator manages a Fortigate model that supports NTurbo. How does NTurbo enhance performance for flow-based inspection?. NTurbo creates two inspection sessions on the FortiGate device. NTurbo offloads traffic to the content processor. NTurbo creates a special data path to redirect traffic between the IPS engine its ingress and egress interface. NTurbo buffers the whole file and then sends it to the antivirus engine.

Refer to the exhibits. The exhibits show a diagram of a FortiGate device connected to the network, VIP configuration, firewall policy, and the sniffer, CLI output on the FortiGate device. The WAN (port1) interface has the IP address 10.200.1.1/24. The LAN (port3) interface hs the IP address 10.0.1.254/24. The webserver host (10.0.1.10) must use its VIP external IP address as the source NAT (SNAT) when it pings remote server (10.200.3.1) Which two statements are valid to achieve this goal? (Choose two.). Create a new firewall policy before Internet_Access for the webserver and apply the IP pool. Disable port forwarding on the VIP object. Disable NAT on the Internet_Access firewall policy. Enable NAT on the Allow_access firewall policy.

Which NAT method translates the source IP address in a packet to another IP address?. SNAT. DNAT. VIP. IP Pool.

Which two statements about equal-cost multi-path (ECMP) configuration on FortiGate are true? (Choose two.). If SD-WAN is disabled, you can configure the parameter v4-ecmp-mode to volume-based. If SD-WAN is enabled, you control the load balancing algorithm with the parameter load-balance-mode. If SD-WAN is disable, you configure the load balancing algorithm in config system settings. If SD-WAN is enabled, you can configure routes with unequal distance and priority values to be part of ECMP.

Fortigate is operating in NAT mode and has two physical interfaces connected to the LAN and DMZ networks respectively. Which two statements are true about the requirements of connected physical interfaces on FortiGate? (Choose two.). Both interfaces must have directly connected routes on the routing table. Both interfaces must have the interface role assigned. Both interfaces must have DHCP enabled. Both interfaces must have IP addresses assigned.

Refer to the exhibits. The exhibits show a diagram if a FortiGate device connected to the network, as well as the firewall policy and IP pool configuration on the Fortigate device. Two PCs. PC1 and PC2, are connected begind FortiGate and can access the internet successfully. However, when the adminstrator adds a third PC to the network (PC3), the PC cannot connect to the internet. Based on the information show in the exhibit, which two configuration options can the administrator use to fix the connectivity issue for PC3?(Choose Three). In the firewall policy configuration add 10.0.1.3 as an address object in source field. In the IP pool configuration. set endip to 192.2.0.12. In the IP pool configuratio, set type to overload. Configure another firewall policy that matches only the address of PC3 as source, and then place the policy on top of trhe list. In the firewall policy configuration, disable ippool.

An adminstrator configured a FortiGate to act as a collector for agentless polling mode. What must the adminstrator add to the FortiGate device to retrieve AD user group information?. RADIUS server. LDAP server. Windows server. DHCP server.

What is eXtended Authentication (XAuth)?. It is an IPsec extension that forces remote VPN users to authenticate using their credentials (username and password). It is an IPsec extension that authenticates remote VPN peers using digital certificates. It is an IPsec extension that authenticates remote VPN peers using a pre-shared key. It is an IPsec extension that forces remote VPN users to authenticate using their local ID.

Which statement about the HA override setting in FortiGate HA clusters is true?. You must configure override settings manually and separately for each cluster member. It reboots FortiGate. It synchronizes device priority on all cluster members. It enables monitored ports.

Which three strategies are valid SD-WAN rule strategies for member selection? (Choose Three.). Best Quality with load balancing. Manual with load balancing. Lowest Quality (SLA) with load balancing. Lowest Cost (SLA) without load balancing. Lowest Cost (SLA) with load balancing.

Refer to the exhibit, which shows an SD-WAN zone configuration the FortiGate GUI. Based on the exhibit, which statement is true?. The d-wan zone cannot be deleted. The d-wan zone contains no member. The underlay zone contains port1 and port2. The virtual-wan-link zone contains no member.

Which route will be selected when trying to reach 10.20.30.254?. 10.20.30.0/24 [10/0] via 172.20.167.254, port3, [1/0]. 10.30.20.0/24 [10/0] via 172.20.121.2, port1, [1/0]. 10.20.30.0/26 [10/0] via 172.20.168.254, port2, [1/0]. 0.0.0.0/0 [10/0] via 172.20.121.2, port1, [1/0].

Which type of traffic inspection requires FortiGate to act as a CA?. SSL traffic inspection when protecting multiple clients connecting to multiple servers. SSL certificate inspection when protecting a local SSL server. SSL certificate inspection when protecting multiple clients connecting to multiple servers. SSL traffic inspection when protecting a local SSL server.

Which two statements are true regarding FortiGate HA configuration synchronization? (Choose two). Checksums of devices are compared against each other to ensure configurations are the same. Checksums of devices will be different from each other because some configuration items are not synced to other HA members. Incremental configuration syncrhonization can occur only from changes made on the primary FortiGate device. Incremental configuration synchronization can occur from changes made on any FortiGate device within the HA cluster.

Which three statements about SD-WAN zones are true? (Choose three.). An SD-WAN zone can contain physical and logical interfaces. You can define up to three SD-WAN zones per FortiGate device. You can use an SD-WAN zone in static route definitions. An SD-WAN zone must contain at least two members. An SD-WAN zone is a logical grouping of members.

Which method allows management access to the FortiGate CLI whithout network connectivity?. CLI console widget. Serial console. SSH console. Telnet console.

Which two IP pool types are useful for carrier-grade NAT deployments? (Choose two.). One-to-one. Fixed port range. Port block allocation. Overload.

An administrator needs to inspect all web traffic (including Internet web traffic) coming from users connecting to the SSL-VPN. How can this be achieved?. Disabling split tunneling. Using web-only mode. Configuring web bookmarks. Assigning public IP addresses to SSL-VPN users.

Which two statements about incoming and outgoing interfaces in firewall policies are true? (Choose two.). Multiple interfaces can be selected as incoming and outgoing interfaces. An incoming interface is mandatory in a firewall policy, but an outgoing interface is optional. A zone can be chosen as the outgoing interface. Only the any interface can be chosen as an incoming interface.

What are the three key routing principles in SD-WAN? (Choose three.). By default, SD-WAN rules are skipped if only one route to the destination is available. Regular policy routes have precedence over SD-WAN rules. By default SD SD-WAN rules are skipped if the best route to the destination is not an SD-WAN member. SD-WAN rules have precedence over any other type of routes. By default, SD-WAN members are skipped if they do not have a valid route to the destination.

FortiGate is configured for firewall authentication. When attempting to access an external website, the user is not presented with a login prompt. What is the most likely reason for this situation?. The user is using a super admin account. No matching user account exists for this user. The user is using a guest account profile. The user was authenticated using passive authentication.

A user at 192.168.32.15 is trying to access the web server at 172.16.32.254. Which two statements best describe how the FortiGate will perform reverse path forwarding (RPF) checks on this traffic? (Choose two). Loose RPF check will allow the traffic. Strict RPF check will allow the traffic. Loose RPF check will deny the traffic. Strict RPF check will deny the traffic.

Which statement best describes the role of a DC agent in an FSSO DC agent mode solution? Select one: It captures the login events and forwards them to the collector agent. It captures the login and logoff events and forwards them to the collector agent. It captures the login events and forwards them to FortiGate. It captures the user IP address and workstation name and forwards them to FortiGate.

Which two settings must you configure when FortiGate is being deployed as a root FortiGate in a Security Fabric topology? (Choose two.). Pre-authorize downstream FortiGate devices. FortiAnalyzer IP address. Fabric name. FortiManager IP address.

Which three methods can you use to deliver the token code to a user who is configured to use two-factor authentication? (Choose three.). Voicemail message. FortiToken Mobile. SMS text message. Email. Instant message app.

What must you configure to enable proxy-based TCP session failover?. You must configure session-pickup-connectionless enable under configure system ha. You must configure session-pickup-enable under configure system ha. You must configure ha-configuration-sync under configure system ha. You do not need to configure anything because all TCP sessions are automatically failed over.

Which three settings and protocols can be used to provide secure and restrictive administrative access to FortiGate? (Choose three.). Trusted host. SSH. Trusted authentication. FortiTelemetry. HTTPS.

There are multiple IPsec VPNs configured in aggressive mode on the HQ FortiGate. The requirement is to connect dial-up users to their respective department VPN tunnels. Which phase 1 setting you can configure to match the user to the tunnel?. Peer ID. Local Gateway. Dead Peer Detection. IKE Mode Config.

Which two statements are correct when FortiGate enters conserve mode? (Choose two.). Fortigate continues to transmit packets without IPS inspection when the fail-open global setting in IPS is enabled. FortiGate refuses to accept configuration changes. FortiGate halts complete system operation and requires a reboot to regain available resources. Fortigate continues to run critical security actions, such as quarantine.

Which two behaviours result from this full SSL configuration? (Choose two.). The browser bypasses all certificate warnings and allows the connection. A temporary trusted FortiGate certificate replaces the server certificate when the server certificate is trusted. A temporary trusted FortiGate certificate replaces the server certificate, even when the server certificate is untrusted. A temporary untrusted FortiGate certificate replaces the server certificate when the server certificate is untrusted.

Refer to the exhibit: The NOC team connects to the FortiGate with the NOC_Access admin profile. They request that their GUI sessions do not disconnect too early during inactivity, What must the administrator configure to answer this specific request from the NOC team?. Increase the admintimeout value under config system global. Increase the offline value of the Override Idle Timeout parameter in the NOC_Access admin profile. Enable the parameter Never Timeout in the admin profile. Increase the admintimeout value under config system accprofile super_admin.

Refer to the exhibit. Which statement about this firewall policy list is true?. The firewall policies are listed by ingress and egress interfaces pairing view. The firewall policies are listed by ID sequence view. The Implicit group can include more than one deny firewall policy. LAN to WAN, WAN to LAN, and Implicit are sequence grouping view lists.

Which two statements about advanced AD access mode for the FSSO collector agent are true? (Choose two.). It uses the Windows convention for naming; that is, Domain\Username. It supports monitoring of nested groups. It is only supported if DC agents are deployed. FortiGate can act as an LDAP client to configure the group filters.

Refer to the exhibit. FortiGate is configured for firewall authentication. When attempting to access an external website, the user is not presented whith a login prompt. What is the most likely reason for this situation?. The user is using an incorrect user name. No mathching user account exists for this user. The Service DNS is required in the firewall policy. The Remote-users group is not added to the Destination.

Which two pieces of information are synchronized between FortiGate HA members? (Choose two.). OSPF adjacencies. DHCP leases. BGP peerings. IPsec security associations.

Which statement about the configuration settings is true?. When a remote user accesses http://10.200.1.1:443, the SSL-VPN login page opens. When a remote user accesses https://10.200.1.1:443, the SSL-VPN login page opens. When a remote user accesses https://10.200.1.1:443, the FortiGate login page opens. The settings are invalid. The administrator settings and the SSL-VPN settings cannot use the same port.

Refer to te exhibit. Which two statements are true about the routing entries in this database table? (Choose two.). Both default routes have different adminstrative distances. All of the entries in the routing database table are installed in the FortiGate routing table. The default route on port2 is marked as the standby route. The port2 interface is marked as inactive.

Which statement about firewall policy NAT is true?. DNAT is not supported. DNAT can automatically apply to multiple firewall policies, based on DNAT rules. You must configure SNAT for each firewall policy. SNAT can automatically apply to multiple firewall policies, based on SNAT policies.

A FortiGate firewall policy is configured with active authentication, however, the user cannot authenticate when accessing a website Which protocol must FortiGate allow even though the user cannot authenticate?. DHCP. DNS. ICMP. LDAP.

A network adminstrator has configured an SSL/SSH inspection profile defined for full SSL inspection and set with a private CA certificate. The firewall policy that allows the traffic uses this profile for SSL inspection and performs web filtering. When visiting any HTTPS websites, the browser reports certificate warning errors What is the reason for the certificate warning errors?. With full SSL inspection it is not possible to avoid certificate warning errors at the browser level. The SSL cipher compliance option is not enabled on the SSL inspection profile. This setting is required when the SSL inspection profile is defined with a private CA certificate. The certificate used by FortiGate for SSL inspection does not contain the required certificate extensions. The browser does not recognize the certificate in use as signed by a trusted CA.

Refer to the exhibit. The adminstrator configured SD-WAN rules and set the Fortigate traffic log page to display SD-WAN-specific columns: SD-WAN Quality and SD-WAN Rule Name. FortiGate allows the traffic according to policy ID 1. This policy that allows SD-WAN traffic. Despite these settings the traffic logs do not show the name of the SD-WAN rule used to steer those traffic flows. What can be the reason?. SD-WAN rule names do not appear immediately. The administrator needs to refresh page. There is no application control profile apllied to the firewall policy. Destination in the SD-WAN rules are configured per application but the feature visibility is not enabled. FortiGate load balanced the traffic according to the implicit SD-WAN rule.

Which two statements correctly describe the differences between IPsec main mode and IPsec aggressive mode? (Choose two.). Six packets are usually exchanged during main mode, while only three packets are exchanged during aggressive mode. Main mode cannot be used for dialup VPNs, while aggressive mode can. Aggressive mode supports XAuth, while main mode does not. The first packet of aggressive mode contains the peer ID, while the first packet of main mode does not.